background image

 EAGLE-II Swing Gate Operator

____________________

Installing the Warning Sign

Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com

(5)

Precautions

Be sure to read and follow all the Eagle Access Control Systems, Inc. and

UL instructions before installing and operating any Eagle Access Control

Systems, Inc. products. Eagle Access Control Systems, Inc. is not responsible

for any improper installation procedures caused by failure to comply with local

building codes.

CAUTION!

!

____________________

Eagle swing gate operators are for vehicular use only! 

They are not for pedestrian use!

____________________

Closing

Be sure to mount ALL operating

devices clearly out of reach  

through gate.

!

!

Regarding Ornamental Grill Styled Gates:

Injuries may be avoided if a mesh or screen is

installed on the gate. Injuries resulting from hands

and feet becoming stuck in gate or children riding

the gate while in movement, can be greatly

reduced if this "screen" or "mesh" is applied

to gate as a safety precaution.

____________________

Install 

Warning Sign

 On 

Both

 Sides Of Gate

The gate attachment bar must run the entire

length of the gate to ensure full strength

Summary of Contents for Power II




















Reviews: