7
Installation
Instruction
8
6. “
”
Jet
Touch “ ” to turn on the
jet
, one admission valve works, touch “
” for the first time, two admission valves work; touch
“ ” for the second time, three admission valves work; touch “ ” for the third time, four admission valves work; touch “ ” for
7.
the fourth time, four admission valves turn off; So the cycle to repeat.
”
Jet Strength
Touch “
” to turn on the
jet strength
, one admission valve works, touch “
” for the first time, air inlet circular with 3 seconds
interval. The order is: one admission valve, two admission valves, three admission valves, four admission valves, three admission valves,
two admission valves, one admission valve. Touch “ ” for the second time, four admission valves work for 2 seconds, and turn off for 1
second. So the cycle to repeat. Touch “ ” for the third time, four admission valves turn off. So the cycle to repeat.
8. “ ” Radio
8.1 Touch the “ ” to turn on the radio when the control system is turn on, the LCD shows the current frequency and “ ” “ ”
icon; touch the “ ” again to turn on the radio, the current frequency and “ ” “ ” icon shows on LCD disappear.
8.2 FM broadcast receiving frequency range is 87.5MHz---108.0MHz.
8.3 Frequency increase
Touch “ ” to increase a step length (1 step length = 50KHz) tuned frequency when the radio turns on. Touch this key for more than
2 seconds, the system would search FM program upwards, digital lock would lock the program automatically, LCD shows the corresponsive
frequency; when it reaches upper limit 108.0MHz and touch this key, the frequency will turn to 87.5MHz.
8.4 Frequency decrease
Touch “ ” to decrease a step length (1 step length = 50KHz) tuned frequency when the radio turns on. Touch this key for more than
2 seconds, the system would search FM program downwards, digital lock would lock the program automatically, LCD shows the corresponsive
frequency; when it reaches lower limit 87.5MHz and touch this key, the frequency will turn to 108.0MHz.
8.5 Volume adjustment
Touch “ ” when radio turns on, LCD flicker “VOL” and number means the volume can be adjusted. Touch “ ” to increase the
volume, touch “ ” to decrease volume. The volume range is 0-20.
8.6 Channel saving/channel picking out
” the LCD flicker “CH” icon, touch “
8.6.1 Channel saving: select the channel need to save when the radio turns on, touch “
”
” to choose the saving position, the channel can be saved in this position when touch “
or “
” for 2 seconds again.
The characteristics of the control system electrical box
1）
AC220V-240V/
AC110V
-
120V
Rated voltage:
2
）
Rated frequency:
50HZ
/
60HZ
3
）
Standby Power:
<10W （
All load is closed
）
4
）
Ambient temperature:
+5℃~+40℃
Devices being controlled by control system
1
）
2HP
2
）
1500W
3
）
DC12V/1W
5
）
Ozone
generator:
DC12V/6W
6
）
Speaker:
8Ω/15W
（
Maximum
）
Surfing
water
pump:
Heater:
Bottom light:
4
）
Electromagnetism valve:
4*DC12V /5W
Control panel operation instruction
1
.
Press any key a buzzer would let out.
2. “ ” On
/
Off
2
.
1 The control system starts operation when touch this key, the bottom lights would turn on at the same time.; press this key again to turn off the control system.
2.2 The control system would turn off automatically when it turn on 60 minutes later, and all the load would turn off.
3.
Child lock
The control system would lock all keys automatically when you do not use the control panel in 5 minutes. The LCD shows “LOCK” icon. To unlock the
control
panel by pressing any key, the “LOCK” icon disappear.
4.
“ ” light
Each time to touch “
” the lights would change to another color, the LCD shows a light icon when the control system turns on; the lights colors
would change circularly when touch “
” for the seventh times; the lights would turn off when touch “
” for the eighth times.
5. “
”
Jet Mode
5.1 There is water level sensor in the control system to prevent water pump from running idle to damage water pump under less water or without water.
5.2 The
jet
function would turn on when touch “
the water level is below the set value, the “
”, the LCD shows “ ” icon. The water pump would not work when the water level sensor test
” icon twinkle. The water pump would start to work when the water level sensor test the water level reaches
to the set value, the “ ” shows dynamic.
5.3 Touch “
” to
turn off the water pump when the
jet
function is turn on, and the
jet
mode
icon would disappear.
Also the heater would turn
off (if the heater is turn on).
TS Control panel instruction
TS Control panel instruction
