Adjusting output level
Twist the head to select between four
output levels. You can pre-select your
desired output
level before
turning on
the flashlight.
Maintenance
Periodically clean the thread and o-rings
with a lint free cloth and apply a thin coat-
ing of EagleTac silicon-based lubricant to
the o-rings.
Clean the battery contact, signal contact
(the gold coated pins and PCB contact
area on the body tube), and machined
thread with a lint free cloth and use a
small drop of Deoxit red cleaner solution
(D100L series) to slightly lube them for
better conductivity and smoother mode
switching experience.
Color and diffuser filter
Kit models come with diffuser and color
filters. Unscrew the stainless steel bezel
and replace it with the filter to use.
Tail-cap with switch
For kit versions that comes with extra
tailcap and body that is setup with rear
signal connection, user may operate the
flashlight with the rear switch.
1) Check and replace batteries
2) Ensure tailcap is tight
3) Clean all conductive contacts
(see maintenance section)
4) Check battery polarity
Troubleshooting - Flashlight does not
turn on or fails to switch between
outputs normally:
1st level
2nd, 3rd,
4th level
“No Hassle” EAGTAC Warranty
For repair, replacement, or other inquiries
contact your EAGTAC dealer. You can also
reach our customer support via email at
support@eagletac.com.
We warrant our flashlights to be free from
defects in workmanship and materials. We will
repair, replace at our option, without charging
any product or part which is found to be
defective under normal use within 120
months from the date of purchase with the
proof of purchase.
Electronics, chargers and rechargeable batter-
ies are covered for a period of 12 months with
purchase receipt. Such repair or replacement
shall be the purchaser’s sole and exclusive
remedy under this warranty. Normal wear and
tear including batteries draining is not
covered, nor is damage resulting from modifi-
cation, misuse, abuse, neglect, faulty battery,
battery leakage, reversed charging damage,
improper maintenance or repaired by anyone
other than EAGTAC or authorized dealer.
Do not touch or attempt to clean the
reflector, as it will damage the reflective
coating permanently.
Hidden AUX. settings
With the head at tight position (1st
level), loosen to 3rd or 4th level and
tighten the head within one second to
enter AUX. setting. Repeat to cycle
through all settings. Turn off the light
or loosen the head to quit.
Strobe (I/II) Hi-Flash S.O.S. (I/II)
Beacon Lo-Flash (Repeat)
Instant Turbo output
At any output level,
press and hold
the
on/off switch for 100% output.
Release
the button to return to previous level.
Instant Strobe output
At any output level (even off ),
double
press and hold
the on/off button switch
for strobe output.
Release
the button to
return to previous level.
Energy saving feature
Enabled by default, this feature
reduces output by 25% (or 10% when
disabled) after 200 seconds at turbo
mode. To toggle this feature, turn on
the flashlight at 4th level, and dial to
3rd level and then back to 4th level for
ten times within five seconds.
To switch between tactical and regular
mode, turn on the flashlight at 1st level,
switch to 2nd level and then back to 1st
level for ten times within five seconds.
Tactical Mode
100%
12%
Strobe I
Strobe II
Regular Mode
100%
45%
8%
1%
Level
1st
2nd
3rd
4th
“Deoxit” is a trademark of Caig Laboratories,
Periodically clean
and apply Deoxit
red to ensure
smooth mode
switching and good
long term reliability.
How to prolong battery life
1) Recharge often. No need to discharge
the battery completely before charging
as li-ion has no memory effect.
2) To prolong li-ion battery life, drain the
battery to 3.75V or below, and discon-
nect it from the flashlight before putting
it in long-term storage.
