background image

The material contained in this document is the property of Electronics & Innovation Ltd., it is subject to 
change without notice.  
 
March 2007                                                                                                                                    Revision B 
 

 

Warranty 

 
Electronics & Innovation Ltd., (hereafter E&I) warrants for the period of one year from the 
date of original delivery, each unit to be free of defects in materials and workmanship. For 
the period of 12 months E&I will, at its option, repair or replace defective parts so as to 
render  the  unit  fully  operational  such  that  it  performs  according  to  the  original 
specifications; free of charge to the original purchaser.  
 
Should warranty service be required, the unit must be returned to E&I, freight cost to be 
borne  by  the  owner.  If,  in  our  opinion,  the  unit  has  been  damaged  by  use  outside  the 
limits prescribed in this manual or by accident, then the warranty shall not be honored. In 
such  a  case  E&I  will  provide  an  estimate  for  repair,  assuming  repair  is  possible  and 
provide a quote at standard service rates. 
 
 
 
 
 

Contents 

 
Chapter 1 
 

General Information……………………………………………………………3 

 

 

 

Chapter 2 
 

Operation………………………………………………………………………..4 

 
Chapter 3 
 

Technical Information………………………………………………………….7 

 
Chapter 4 
 

Maintenance……………………………………………………………………8 

 
Chapter 5 
 

Safety……………………………………………………………………………12 

 
 

Summary of Contents for 1040L














Reviews: