background image

INTRODUCTION

HVLP stands for High Volume, Low Pressure. This is
a type of spraying that allows you to spray extremely
accurately but without all the overspray that occurs
with the high pressure tank type equipment. In fact, in
some parts of the world the high pressure systems
are banned by law on environmental grounds and
HVLP type systems are the only alternative for
professional type spraying. This gun is extremely
easy to use, very safe and reduces the amount of
paint used.

PLEASE NOTE

We have done all we can to ensure that used correctly and
according to these instructions, this spray gun will give long
and trouble free life. We accept no responsibility for damage
caused by the use of incorrect or unsuitable substances,
paints or fluids which have not been thinned correctly or are
unsuitable for the surfaces to which they are applied, health
hazards arising from lack of ventilation when working in
confined spaces or failure of the equipment due to
inadequate cleaning of the components after use. If in doubt,
always test a small inconspicuous area first. Always read the
paint manufacturer’s instructions first. Neither our guarantee
nor the above statement affects your statutory rights.

6

Summary of Contents for Spray Station 3000

























Reviews: