background image

MAINS CONNECTION

This unit is a Class II appliance which means it is double-insulated for your protection, no earthing wire is

necessary.

If the supply cord is damaged, it must be replaced by Earlex Ltd or our appointed agents.

Your unit has been supplied with a mains lead fitted with a fuse plug. This is identified by the fuse holder in

the base of the plug. Please read the following safety instructions before use.

1

. If the fitted plug is cut off from the mains lead then the plug must be disposed of safely. 

NEVER

under

any circumstances insert such a plug into a 13 Amp socket-outlet.

2. NEVER

under any circumstances use the appliance or mains lead without the fuse cover fitted.

This is the little cover fixed into the base of the plug to hold the fuse in place.

3. 

If you lose the fuse cover then please contact any electrical dealer for a replacement or ring our helpline.

4

. A replacement fuse must be rated at 5 Amps. These must be manufactured and approved to BS 1362.

5. IF IN ANY DOUBT CONTACT A QUALIFIED ELECTRICIAN.

If you need to fit a plug to the mains lead, this should be fitted in accordance with the wiring instructions

below, and will need to be used with a 5 Amp fuse approved to BS 1362. If in doubt consult a qualified

electrician.

If you are using an extension lead it must be rated at a minimum of 6 Amps and fully unwound. Do not

operate with a lead rated at less than 6 Amps as this will cause premature failure of the motor which is not

covered by the guarantee.
As  the  colours  of  the  wires  in  the  mains  lead  of  the  application  may  not  correspond  with  the  coloured

markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal which is

marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which

is marked with the letter L or coloured red.

INFORMATION ON THE DISPOSAL OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT

KNOWN AS WEEE

Your  attention  is  brought  to  new  directives  applicable  to  the  disposal  of  this  electrical

equipment, where in accordance with the legislation this product must not be disposed of in

your normal household waste. Instead it is your responsibility to dispose of this type of waste

by  handing  it  over  to  special  designated  collection  points  for  recovery  and  recycling.  This

product is marked with a ‘Wheelie bin’ symbol with a cross on it to remind you of this action.

The objective of this directive is to help conserve resources and ensure that it is recycled in a

manner that protects human health and the environment. For more information about where

you can drop off your waste please contact your local authority, take back facilities are free of

charge.

9

Summary of Contents for SPRAY SYSTEM HV 1900













Reviews: