No. Description
Part No.
1. Needle and Fluid Tip Tool
V0018
2. Air Cap Ring
V0001
3. Air Cap
V0002
4. Spray Direction Plate
V0003
5. Fluid Tip 2.0mm
V0004
6. Fluid Tip O-Ring
V0005
No. Description
Part No.
7. Fluid Needle 2.0mm
V0006
8. Lip Seal - Fluid Needle
V0007
9. Paint Flow Adjuster
V0011
10. Paint Container Seal
L0682
11. Pick-Up Tube
V0012
12. Paint Container
V0014
• NEVER under any circumstances aim the
>
Spray Gun at another person or animal. In
>
the event of injury occurring seek expert
>
medical advice immediately.
• The spray gun must only be used with paints
>
and solvents that have a flash point suitable
>
for spraying. If in doubt, consult the paint or
>
solvent manufacturer’s data.
• Always ensure there is adequate ventilation
>
when spraying.
• NEVER spray near a naked flame, including
>
appliance pilot flame.
• NEVER smoke whilst spraying.
• NEVER allow children to operate or play with
>
the spray gun.
• Always read the solvent manufacturer’s
>
instructions before use.
• Always disconnect unit from mains supply
>
when filling the paint container.
• Always wear a suitable protective mask when
>
spraying. We also recommend the use of ear
>
protection, gloves, goggles and overalls.
• After each use, thoroughly clean the spray
>
gun.
• This appliance can be used by children aged
>
from 8 years and above and persons with
>
reduced physical, sensory or mental
>
capabilities or lack of experience and
>
knowledge if they have been given supervision
>
or instruction concerning use of the appliance
>
in a safe way and understand the hazards
>
involved. Children shall not play with the
>
appliance. Cleaning and user maintenance
>
shall not be made by children without
>
supervision.
• If the supply cord is damaged, it must be
>
replaced by the manufacturer or its appointed
agents to avoid a safety hazard.
• Use only genuine manufacturer replacement
>
parts.
• Always disconnect the Spray Station from the
>
mains supply before cleaning the appliance.
•
WARNING!
The use of any accessory or
>
attachment, other than those recommended in
>
this instruction manual, may present a risk of
>
personal injury.
• Use the Spray Gun for the job it was designed
>
for only. Misuse of the Spray Gun will
>
invalidate the guarantee.
WARNING! The substances used with this
Spray Gun (paints, solvents, etc.) may
contain dangerous, harmful, explosive or
corrosive materials. ALWAYS COMPLY WITH
THE SAFETY INSTRUCTIONS ISSUED WITH
THIS PRODUCT AND THE MATERIAL BEING
USED.
The concept
A motor feeds out a high volume of air (HV) and enables products to be sprayed at a low pressure (LP). The air hose feeds the air produced by the
motor to the spray gun. The solution is released from the fluid tip of the spray gun at a very low pressure and is enclosed in a high volume of air.
The powerful motor can spray a wide range of solutions with or without dilution. However, there will always be some which will not be suitable for
the spray gun. Good quality paint contains a high percentage of solids which make the dilution easier. The users must keep in mind that low
temperatures make the paint thicker, that’s why we recommend spraying with the Spray Gun at a 15°C minimum temperature.
4
TECHNICAL SPECIFICATION
HV5900
Wattage:
650
Watts
Container capacity:
1
litre + 5 litre spraypack
Voltage:
220-240
V
Frequency:
50-60Hz
Air hose length:
4m
Dynamic air pressure:
0,16
bar
Sound pressure level:
80
dB (A)
No. Description
Part No.
13. Air Hose
L2249
14. Filter
L0290
FOR SPRAYPACK ASSEMBLY PLEASE REFER TO SPRAYPACK MANUAL.
SAFETY OPERATING INSTRUCTIONS
PLEASE READ BEFORE USE
PARTS LIST
Fig.1
PARTS LIST
Fig.2
INTRODUCTION
Maximum viscosity:
220
DIN/s
EN
Summary of Contents for SPRAYSTATION 5900
Page 11: ...11...
