background image

11

We are pleased to welcome you to our ever-growing family of drummers and sound 
engineers using Earthworks High Definition Microphones™ for recording and live 
sound. 

We  hope  the  suggestions  in  this  manual  have  been  beneficial  to  you.  Don’t  be 
afraid to experiment with mic placement.  You can be as creative with your micro-
phone placement as you are with your music.  You are the judge of what works 
best and sounds best. 

If you have any questions, or require any additional information, feel free to 
contact Earthworks directly using the contact information on the back cover of 
this manual and don’t forget to register your warranty information on the Earth-
works website, (see information below).

EARTHWORKS WARRANTY

All  Earthworks

®

  products  carry  a  limited  warranty  (parts  and  labor). 

Please register your warranty at www.earthworksaudio.com/register 

If you have any problems with your Earthworks products, please contact 

our warranty/repair department by email at
returns@earthworksaudio.com or by telephone at (603) 654-2433, ext 119.

Figure 10-A and 10-B  Miking the Top Head of a Tom

A

B

Summary of Contents for CMK4 CloseMic Kit

















Reviews: