background image

Congratulations on your purchase of the Earthworks DK7 DrumKit™ High 
Definition Multi-microphone Drum System. When compared to conventional 
drum mics, Earthworks mics will provide more detail in the attack, reproduce 
subtle  low  level  details,  near-perfect  polar  response,  far  less  phase  issues 
whenclose miking and nearly twice the amount of rear rejection. We welcome 
you into an entire new world of pristine drum sound using Earthworks High 
Definition Drum Microphones™.  

Happy Drumming!

Please verify that you have received everything listed below.

Included with the DK7 DrumKit™ Drum Microphone System:

2 – SR25 Cardioid Microphones (overheads)

4 – DM20 DrumMic™ (toms & snare) 

1 – SR20LS (kickdrum)

4 – RM1 RimMount™ (for DM20s)

3 – SRW3 Foam Windscreens (for SR25s & SR20LS)

4 – PW1 Windscreens (for DM20s)

1 – High Impact Carrying Case

      with custom foam insert

1 – User’s Manual   

Version 10  May 1, 2018

1

Before You Start

When connecting the DK7 condenser microphones to a preamp with phantom 
power, allow up to one minute for the microphone to settle. Plugging in the 
microphone “hot” 

(phantom power already present at the input) 

will not damage 

the microphone, and is actually preferred for faster settling. It is normal for any 
phantom powered mic to “pop” when plugged in or powered up. Make sure to 
mute the signal to speakers and/or headphones when phantom power is first 
applied.

Summary of Contents for DrumKit DK7

















Reviews: