55
3.1
HEAT MODE
1
0
1
1
/
3.2
t_T4_FRESH_H
0.5
0.5
6
0.5
horas
3.3
T4HMAX
25
20
35
1
℃
3.4
T4HMIN
-15
-25
15
1
℃
3.5
dT1SH
5
2
10
1
℃
3.6
dTSH
2
1
10
1
℃
3.8
T1SetH1
35
25
60
1
℃
3.9
T1SetH2
28
25
60
1
℃
3.10
T4H1
-5
-25
35
1
℃
3.11
T4H2
7
-25
35
1
℃
3.12
ZONE1 H-EMISSION
1
0
2
1
/
3.13
ZONE2 H-EMISSION
2
0
2
1
/
3.14
t_DELAY_PUMP
2
2
20
0.5
MIN
4.1
T4AUTOCMIN
25
20
29
1
℃
4.2
T4AUTOHMAX
17
10
17
1
℃
5.1
WATER FLOW TEMP.
1
0
1
1
/
5.2
ROOM TEMP.
0
0
1
1
/
5.3
DOUBLE ZONE
0
0
1
1
/
7.1
dT1_IBH_ON
5
2
10
1
℃
7.2
t_IBH_DELAY
30
15
120
5
MIN
7.3
T4_IBH_ON
-5
-15
10
1
℃
7.7
IBH_LOCATE
0
0
0
0
℃
7.8
P_IBH1
0
0
20
0.5
kW
7.9
P_IBH2
0
0
20
0.5
kW
7.10
P_TBH
2
0
20
0.5
kW
7.4
dT1_AHS_ON
5
2
10
1
℃
7.5
t_AHS_DELAY
30
5
120
5
MIN
7.6
T4_AHS_ON
-5
-15
10
1
℃
8.1
T1S_H.A_H
25
20
25
1
℃
8.2
T5S_H.A_DHW
25
20
25
1
℃
12.1
PREHEATING FOR
FLOOR T1S
25
25
35
1
℃
12.3
t_FIRSTFH
72
48
96
12
HOUR
6.1
ROOM THERMOSTAT
0
0
3
1
/
Activar o desactivar el modo de calefacción
Tiempo de actualización de las curvas relacionadas
con el clima para el modo de calefacción.
Temperatura ambiente máxima de funcionamiento para el
modo de calefacción.
Temperatura ambiente mínima de funcionamiento para
el modo de calefacción.
Diferencia de temperatura para arrancar la unidad (T1)
Diferencia de temperatura para iniciar la unidad (Ta)
Temperatura de ajuste 1 de las curvas relacionadas con
el clima para el modo de calefacción
Temperatura de ajuste 2 de las curvas relacionadas con
el clima para el modo de calefacción
Temperatura ambiente 1 de las curvas relacionadas con
el clima para el modo de calefacción
Temperatura ambiente 2 de las curvas relacionadas con
el clima para el modo de calefacción
El tipo de fin de la zona 1 para el modo de calefacción: 0 =
FCU (unidad de fancoil), 1 = RAD. (Radiador), 2 = FLH
(calefacción de suelo radiante)
El tipo de fin de la zona 2 para el modo de calefacción: 0 =
FCU (unidad de fancoil), 1 = RAD. (Radiador), 2 = FLH
(calefacción de suelo radiante)
Tiempo que ha funcionado el compresor antes de
arrancar la bomba.
Temperatura ambiente mínima de funcionamiento para
enfriar en modo automático
Temperatura ambiente de funcionamiento máxima para
calentar en modo automático
Habilita o deshabilita la TEMP. FLUJO AGUA:0=NO,1=SÍ
Habilita o deshabilita la ROOM TEMP.:0=NO,1=SÍ
Habilita o deshabilita la DOBLE ZONA
termostato de pared:0=NO,1=SÍ
Diferencia de temperatura entre T1S y T1 para
iniciar el calentador de respaldo.
Tiempo que el compresor ha funcionado antes de
que se encienda el primer calentador de respaldo
Temperatura ambiente para iniciar el calentador de respaldo
Ubicación instalación IBH/AHS BUCLE TUBERÍA=0; TANQUE=1
Corriente entrada IBH1
Corriente entrada IBH2
Corriente entrada TBH
Diferencia de temperatura entre T1S y T1B para
encender la fuente de calefacción adicional
Tiempo que ha funcionado el compresor antes de
poner en marcha la fuente de calefacción adicional
Temperatura ambiente para iniciar la fuente de calor
adicional.
Temperatura objetivo de salida del agua para la calefacción
de espacios cuando está en modo vacaciones.
Temperatura objetivo de salida del agua caliente
sanitaria en el modo de vacaciones.
Temperatura de ajuste del agua de salida durante
el primer precalentamiento del suelo.
Tiempo que dura el precalentamiento del suelo.
Tipo de termostato de pared 0=NO,1=MODO
SET,2=ZONA ÚNICA,3=ZONA DOBLE
V.2
Summary of Contents for ETH220VMA
Page 164: ...V 2...