background image

To order parts and supplies: 800.345.1178  >>  eastwood.com 

5

 

HEALTH AND INJURY HAZARDS!

•  Dust and fine particles are generated while sanding or grinding which can 

contain hazardous or toxic substances. Breathing this dust can cause many 
serious respiratory health conditions. Always use NIOSH approved respira-
tory protection while using this Sander.

•  This Sander will eject particles, dust and sparks at high velocity during op-

eration. Wear approved eye and skin protection at all times while operating.

•  Sanding or grinding with this Sander can generate excessive noise. Wear 

appropriate hearing protection while using.

•  The rotating Disc of this Sander can quickly catch loose clothing, long hair 

or jewelry causing serious personal injury. Keep all loose clothing, long hair 
and jewelry away from operating Sander.

•  This Sander can quickly start up when handling while plugged in to electri-

cal supply causing serious personal injury. Always unplug the tool from the 
electrical supply before changing Sandpaper, making adjustments to the 
tool or performing maintenance.

•  Sharp metal edges can cut. Always wear protective work gloves while 

handling.

•  Rotating abrasive surface can quickly remove flesh. Keep hands and 

fingers away from rotating disc.

•  This Sander can quickly and violently propel workpiece objects while oper-

ating causing injury and or property damage. Do not apply excessive force 
to Sander while in use. Always make sure the workpiece or material being 
cut is held securely and work is done only on the left side of the Disk.

•  If excessive vibration is felt, discontinue use immediately and disconnect 

tool from electrical supply. Inspect abrasive Platen or components for  
damage. Do not resume use until resolution is found.

 

•  This Sander will eject a trail of sparks at high speed which can ignite  

flammable materials or injure others nearby. Do not operate in the  
vicinity of flammable materials and keep all persons and pets away  
from the work area.

ADDITIONAL SAFETY INFORMATION

Summary of Contents for 21535













Reviews: