background image

 
 

 

 

 

 

 

 

      

 

WARNING 

 

CLEARANCES TO COMBUSTIBLES 

 

Location of flammable or explosive objects, liquids or vapours close to the 

appliance may cause fire or explosion and result in property damage, injury or death. 
Do not use, store or locate flammable or explosive objects, liquids or vapours in 
proximity of the appliance.  

The clearance to combustible material represents the minimum distance that 

must be maintained between the outer heater surface and a nearby surface. The stated 
clearance to combustible represents a surface temperature of  90 F (50 C) above room 
temperature. It is the installer's responsibility to ensure that building materials with a low 
heat tolerance, which may degrade at lower temperatures, are protected to prevent 
degradation. 

Minimum 24” must be provided at the centre of the appliance for burner 

servicing.  W hen venting through a wall the vent terminal must be located at least 7.0 ft 
above grade. This appliance must be mounted at least 7 ft above the floor in Canada, 
and 8 ft above the floor in the U.S. 

Anyone in the proximity of the appliance should be alerted to the hazards of high 

surface temperatures and should stay away to avoid burns or clothing ignition. Clothing 
or other flammable materials should not be hung from the appliance, or placed  on or 
near the heater. 

Any cover removed from the appliance must be replaced prior to operation of the 

heater. 

Do not use this appliance if any part has been under water. Immediately call a 

qualified service technician to inspect the appliance and to replace any part of the 
control system and any gas control, which has been under water. 

 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for PPRTH-50-15














































Reviews: