background image

 
 

RECOMMENDED MAINTENANCE

 

Improper adjustment, alteration, service or maintenance can cause property damage, injury or 
death. This heater must be installed and serviced only by a trained gas service technician. 
 
Inspect the entire heater system; venting and gas supply connections, at least annually prior to 
the heating season.  Replace worn parts and repair deficiencies. 
 
Check the inlet air opening and the blower periodically, cleaning off any lint or foreign matter. It 
is important that the flow of combustion and ventilation air must not be obstructed. 
 
The tube heater burner is completely factory assembled and tested. Any alteration voids the 
certification and manufacturer’s warranty. For additional information, contact your local 
distributor, or the manufacturer. 

 
 

WARRANTY

 

ALL Easy Radiant “

Works

” heaters are covered by a 3-year guarantee.  All heaters 

manufactured by Easy Radiant Works are warranted to the original user against defects in 
materials and workmanship under normal use for a period of 3 years from date of purchase.  
Any part that is determined to be defective in material or workmanship during the warranty 
period, and returned shipping costs prepaid, will be, as the exclusive remedy, repaired or 
replaced at the discretion of Easy Radiant Works.  For warranty claim procedures see “Prompt 
Disposition of Warranty Claims” below. 
 
To the extent allowable under applicable law, Easy Radiant Works liability for consequential or 
incidental damages is expressly disclaimed.  Easy Radiant Works liability in all events is limited 
to and shall not exceed the purchase price paid. 
 
Many jurisdictions have codes and regulations governing sales, construction, installation, and/or 
use of products for certain purposes, which may vary among jurisdictions.  While Easy Radiant 
Works attempts to assure that its products comply with these many codes, it cannot guarantee 
compliance, or cannot be responsible for how the product is installed or used.  Before purchase 
or use of a product, review the product applications, and all applicable national and local codes 
and regulations, and ensure that the product and installation will comply with them. 
 

 

 

PROMPT DISPOSITION OF WARRANTY CLAIMS 

Easy Radiant Works will make a good faith effort for prompt correction or other adjustment with 
respect to any product that proves to be defective in material or workmanship within the 
warranty period.  For any product believed to be defective under this warranty, first write or call 
the dealer / retailer from whom the product was purchased.  The dealer / retailer will give further 
instructions.  If unable to resolve satisfactorily, write or call Easy Radiant Works at the address 
above giving dealer’s name, address, date and number of dealer’s invoice, and describe the 
nature of the defect.  Title and risk of loss pass to buyer on delivery to common carrier.  If 
product is damaged in transit to you, file a claim with the carrier. 
 
 
 

 
 

Summary of Contents for PPRTH-50-15














































Reviews: