When user use remote engine start function, please pay attention to following points:
(1) Never remote start the vehicle with the vehicle in gear, and
(2) Never remote start the vehicle with the keys in the ignition. The user will be responsible for having the
neutral safety feature of the vehicle periodically checked, where in the vehicle must not remote start while the
vehicle is in gear. This testing should be performed by an authorized EASYGUARD dealer or a professional
car alarm installer in accordance with the safety checking stated in this product installation guide. If the
vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem
immediately.
(3). When use remote engine start function, the gear selector should in Neutral (N) or
position. If
your vehicle is manual transmission, please refer to remote engine start for manual gear car.
Remote starters for manual transmission pose significant risks if not properly installed and operated. When
testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat
surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind
the vehicle.
(4). EASYGUARD electronics will not bear any responsibility for the loss caused by the running of the vehicle
after remote engine start.
Parking
(
P
)
1.Remote engine start for automatic gear car:
In arm status, keep pressing the start button on the remote control for 3 seconds will remote start the vehicle.
When doing this, please keep a distance of at least 8 meters away from the vehicle (User is not able to use
remote engine start function if in PKE induction area). Siren will beep 3 times and turn signal lights will flash
15 times when car is remote started. If user approached the vehicle with key fob within PKE induction range,
turn signal light will stop flashing. And the door will be automatically locked once vehicle is started.
The started engine will keep on running for 15 minutes then turn off automatically if user doesn’t unlock the
vehicle doors within 15 minutes.
While the engine is remote started, if user approach the vehicle within 1-2 meters with the remote control, the
door will unlock and the alarm will disarm automatically. The user may drive the vehicle directly and there is
no need to start the engine again.
While the engine is remote started, If user approach the vehicle within 1-2 meters with the remote control but
not open car door, then walk away from the vehicle for more than 5 meters away, the vehicle will be
automatically cut off engine and turn off ACC, ON and enter into arm status.
While the engine is remote started, If user approach the vehicle within 1-2 meters with the remote control and
open car door, then walk away from the vehicle for more than 5 meters away with remote control, the vehicle
engine will not cut off and turn signal light will keep lighting on to remind user to close the door well.
Any illegal door opening will trigger the alarm if without induction of the remote control.
Once the vehicle is remote engine started, keep pressing the start button on remote control for 3 seconds will
remote cut off the engine and also turn off ACC & ON. The vehicle will enter into arm status.
2.Remote engine start for manual gear car:
If the engine is stopped by pressing the push start button then user can’t use remote engine start function. If
user want to start the engine with remote control, please set with below procedure:
Un-plug the 6-Pin ignition wire harness from the control module
Press up DIP switch 5 on control module to set the alarm fit for manual transmission car
Re-plug the 6-Pin ignition wire harness with the control module
Park the vehicle, shift the gear selector to Neutral position, pull the hand brake ON, do not turn off the vehicle
engine in the vehicle with the push start button, exit the vehicle and close all the doors well, walk away from
the vehicle at least 5 meters away, then keep pressing the start button for 3 seconds to turn off the engine.
Then next time user can use the remote control to use remote engine start function. (This is to avoid accident
for manual gear cars if the gear selector is not in neutral position when starting the engine with remote
control).
Important: Factory default setting of this system is with remote engine start for automatic gear cars. If your car
is manual gear cars and want to use the remote engine start function. Please follow with above instructions.
Our company will not bear any responsibility for the loss caused by the running of the vehicle after remote
engine start.
10. Dome light supervision (optional)
If you want to use dome light supervision, please follow with below instruction:
a.Dis-connect the blue/black door trigger wire in 20 pin wire harness with the door trigger wire in your vehicle
b.Un-plug the 6 pin ignition wire harness to cut off power of the device first
c.Press down DIP switch 2 on alarm control module & wait for around 5 minutes
d.Re-plug 6 pin ignition wire harness to re-power the device.
Then you should able to use dome light supervision function now.
If you connect the blue/black door trigger wire with the door trigger wire in your vehicle, the turn signal light
will flash when opening the car door.
If you dis-connect the blue/black door trigger wire with the door trigger wire in your vehicle, the turn signal
light will not flash when opening the car door.
8. To enable or disable PKE feature (PKE ON/OFF setting)
To disable PKE feature(valet mode): Started the vehicle, stepping on foot brake pedal, keep pressing lock &
unlock button on key fob at the same time for 5 seconds, siren beeps 5 times and turn signal light flashes
5 times. The alarm is enter into car valet mode & disable the PKE feature.
To enable PKE feature (exit valet mode): Started the vehicle, stepping on foot brake pedal, keep pressing lock &
unlock button on the key fob
at the same time
for 5 seconds, siren beeps 3 times and turn signal light
flashes 3 times. The vehicle is exited valet mode & enable PKE feature.
Important: The PKE function default is turn on. When PKE function is turn on, press lock button
once
will turn off the PKE function and lock the vehicle door at the same time. If user want to turn the PKE
on again, just press unlock button
once will turn on the PKE function, at the same time the
vehicle door is unlocked temporary.
9.Remote engine start/stop
For a 3 button remote control, the button except lock button and unlock button is the start button.
For a 4 button remote control the button except lock , unlock & trunk release button is the start
button (usually is siren button)
The alarm has two modes for remote engine start, automatic gear car and manual gear car, please
remember to select correct DIP switch selection on the control module. Default setting is for automatic gear
car with switch 5 in control module is press down.
-36-
©
EASYGUARD
Electronics
.
All
right reserved.
-35-
©
EASYGUARD
Electronics
.
All
right reserved.
