7.If you use password entry function to unlock the vehicle but not open and close the vehicle door in 15
seconds, the door will be re-lock automatically after 15 seconds.
8.If you unlock car door by password and open but forget to close the door, the siren will beep for every 5
seconds to remind you to close the door well.
b.Use touch password to lock the vehicle:
1.Stop the vehicle and close the door well, user stand outside the vehicle and input C0#+6 digital password in
turn. Every time you input, the red LED1 on the password key pad will blink once to indicate that the input is
valid, if the red LED1 not blink, please re-input again.
2.If password is correct, once you finish the input, the blue LED2 light will blink 3 times, then turn off. The
vehicle door will be automatically locked.
3.If the password is not correct, the blue LED2 will turn off directly and you need to input the password again.
4.If you input wrong number, please press C button once to cancel.
If user lost the remote control or put the remote control in the vehicle, then can input password to lock the
vehicle door.
d.Password re-set
If you forget the password, you need to re-set the password to default password first, operation is as below:
c.Password revision, please follow with below steps:
1. In disarm status, turn on ACC or ON, continue to press unlock button on remote twice, the blue LED2 on
the keypad is illuminated continuously, this indicate the system is enter into password revision status.
2. Type in factory-set password (123456) directly(no need to input C0#), every time you input, the red LED1
will blink once to confirm the input is valid, once you finished input, then blue LED2 will blink 3 times and horn
sounds once to confirmed the old password is correct. Then the blue LED2 on the password keypad is
illuminated continuously again.
3. Type in new six digital number password (from 0 to 9) and blue light blinks 3 times. Then illuminated
continuously again.
4. Input the 6-digital number new password once again, then blue LED2 blinks 3 times again and then turn
off, at the same time the siren beeps 3 times if car siren is connected with the alarm. This means new
password correct revised and confirmed.
5. If the password not match with the password as step 3 input, the blue LED2 will turn off directly and
password not succeed revised.
6. Now input C0#+new 6 number revised password to see if you can unlock or lock car door with the new
password. If yes, it means that the new password is revised successfully. If not, please check with above
steps again.
Reminder: as the password entry keypad is a touch keypad, so every time when you input a password, the
red LED1 will blink once to confirm it, if the red LED1 not blink, this means the password not enter
successfully, and need to re-input it again.
Reminder:
If you install the touch password keypad, please remember to revise the password once you finish the
installation.
15.Power off memory
If the vehicle was cut off power suddenly, the vehicle will be automatic back to the previous status when re-
power.
16.Door unlock well warning
When the user walk away from the vehicle with remote control but not properly close the door well, turn signal
will flash 3 times and siren beeps 3 times to remind the user to close the door well.
17.Alarm reminder
Once the vehicle is triggered in alarm status, when disarm it, siren will beep once and turn signal light will
flash 3 times to remind the user.
18.Door opening while driving warning
When the vehicle is running but door is opening, turn signal light will flash to remind other vehicle behind. If
the vehicle door is closed, the turn signal light will stop flashing.
19.ACC ON warning
When ACC ON is turn on and remote control was taken away, siren will beep to remind user to turn off it.
20.Emergency override
If the remote control was lost, and user also forget the password preset, need to do an emergency override to
use the vehicle. Step is as below:
Using mechanical key to unlock the vehicle door (will trigger the alarm), then open car door, keep stepping on
foot brake pedal, keep pressing the programming switch on control module for 5 seconds will emergency
override the alarm and can start the vehicle now.
Important: once the vehicle is emergency override, all the alarm function will lost at the same time.
21.Power saving & car battery low power protection
Once the remote control not been used for more than 36 hours or the vehicle battery is lower than 11.8V, the
system will enter into sleep mode automatically and turn off PKE function to save power.
22.Automatic window closing(optional)
Turn off the engine, get off the vehicle and close all the doors well. After locking the doors and arming the
vehicle, the system will detect whether the windows are closed or not and roll up the unclosed windows
automatically. (Note: some cars need extra window closer module to fulfill this function)
Warning: When you leave the vehicle with remote control and lock the vehicle door, please make sure
that there is no passenger, especially child whose body is staying on the slide rail of the open window to
avoid any injury.
1. Make sure the remote control is in PKE detecting range and disarm the vehicle
2. Continue to press the programming switch (please refer to Programming switch in the user manual) for at
least 10 times, then you will heard the siren beeps 3 time, this means the password changed to default
password 123456 already.
3. Then follow with above password revision steps to revise the password to a new one.
Important: If user use the remote control to lock or unlock the vehicle, then you can use the remote
control & touch password key pad to unlock or lock it.
-40-
©
EASYGUARD
Electronics
.
All
right reserved.
-39-
©
EASYGUARD
Electronics
.
All
right reserved.