Dear Customer,
Thank you for purchasing our EASYGUARD EC002 series PKE car alarm with push start stop button. This
alarm is combine with latest PKE (passive keyless entry) technology, remote engine start, keyless go and
touch password entry backup function. Please read the user manual and wire diagram carefully before you
start installation. Once the alarm is properly installed, it can improve the safety of your vehicle greatly.
This product can work with fuel-injected, automatic transmission, or vehicles with manual transmissions
DC12V vehicles.
-01-
©
EASYGUARD
Electronics
.
All
right reserved.
Use of this product in a manner contrary to its intended mode of operation may result in property damage,
personal injury, or death. Except when performing the safety checking indicated in this installation guide.
(1) Never remote start the vehicle with the vehicle in gear, and.
(2) Never remote start the vehicle with the keys in the ignition. If the vehicle starts in gear, cease remote start
operation immediately and consult with the user to fix the problem immediately.
(3). When use remote engine start function, the gear selector should in Neutral (N) position. If your vehicle is
manual transmission, please refer to remote engine start for manual gear car.
Remote starters for manual transmission pose significant risks if not properly installed and operated. When
testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat
surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind
the vehicle.
This product should NOT be installed in any convertible vehicles, soft or hard top. Installation in such vehicles
may pose certain risk.
1.Check the packing list:
Full set device should include following components:
Control module x1
Key fob x2
Push start button x1
Alarm high frequency antenna: x1(with red color connector)
PKE antenna: x2
Touch password keypad: x1
6P ignition wire harness: x1
20P wire harness: x1
3 color (orange, white, yellow) GWR wire x1 or (shock sensor x1)
Note: if the device equip with 3 color (orange, white, yellow) GWR wire, then there is no shock sensor in the
kit, vice versa.
English user manual & wiring diagram x1
-02-
©
EASYGUARD
Electronics
.
All
right reserved.
1.Before Starting the Installation
Please read all the installation guide before starting the installation. The installation of this PKE car alarm with
remote start system requires interfacing with many of the vehicle’s systems. Many new vehicles use low-
voltage or multiplexed systems that can be damaged by low resistance testing devices, such as test lights
and logic probes (computer safe test lights). Test all circuits with a high quality digital multi-meter before
making connections.
Do not disconnect the battery if the vehicle has an anti-theft-coded radio. If equipped with an air bag, avoid
disconnecting the battery if possible. Many airbag systems will display a diagnostic code through their warning
lights after they lose power. Disconnecting the battery requires this code to be erased, which can require a
trip to the car dealer.
To avoid accidental battery drainage, turn off the interior lights or remove the dome light fuse.
Roll down a window to avoid being locked out of the car.
Installation Guide
This product is intended to be installed by a professional car alarm installer only! Any attempt to install this
product by any person but not a trained professional car alarm installer may result in severe damage to the
vehicle or the components.
If user want to do the DIY installation, please study all the user manual and wiring diagram carefully before
you start installation and only make sure you understand everything then start the installation. You may need
to search on the internet for your vehicle wiring diagram if necessary, and learn how to find the related wires
and how to connect them properly.
Once you find correct wires, please solder them well or use crimp connectors to connect the wires well when
finished the wire connection to avoid any loose up when the vehicle running and cause the device failed to
work. If there is any questions, please contact EASYGUARD authorized dealer or contact EASYGARD
electronics directly for help.
IMPORTANT:
The following safety warnings must be observed at all the time:
Due to the complexity of this system, installation of this product must be finished by a professional car alarm
installer or trained alarm installer.
Once the product is properly installed, this system can remote start the vehicle by a command signal from the
remote control Therefore, never operate the system in an area that does not have adequate ventilation. The
following precautions are the sole responsibility of the user; however, authorized EASYGUARD Electronics
dealers should make the following recommendations to all users of this system:
1.Never operate the system in an enclosed or partially enclosed area without ventilation (like a garage).
2. When parking in an enclosed or partially enclosed area or when having the vehicle serviced, please do not
use the remote engine start feature.
3.It is the user's sole responsibility to properly handle and keep out of reach from children all remote controls
and other accessories in the kit to assure that the system does not remote start the vehicle occasionally.
USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT
TO THE VEHICLE . ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR
PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL THE TIMES.
Safety warning!