Customer service: 0303 031 0777
For more innovative products from Easylife please visit:
www.easylifegroup.com
For example if you live in the UK simply press the A button 5 times till the watch says “UK”
4. Press the B button to confirm your selection once the watch has said the local signal / reception
you require.
•
After the confirmation, the watch will run to the local time of the country / signal you have selected.
•
Please wait until the watch hands stop spinning fast and resume to normal running.
•
During “British Summer Time” or “Daylight Saving Time” you may find the time is incorrect by
one hour. This will be corrected after a local signal / reception has been updated. The watch will
synchronise with the local atomic clock automatically at 03:00AM so you have to make sure that
the right country has been set or the watch will not be able to pick the local signal.
•
Please allow up to 15 minutes for the watch to successfully pick up the local signal you have
requested. If the signal has not picked up using the automatic time settings please follow the next
set of instructions for the manual signal settings.
Set Country (with manual signal settings)
The watch must be set to the correct country / signal before can proceed with the following manual
signal settings (see the previous set of instructions “Set Country with automatic time settings”).
In order to set your watch to a local signal follow the steps below:
1. Press the A button (next to 2 o’clock) until the second hand spins round to the 12 o’clock position.
2. Simply leave the watch on a window ledge or a place where it will pick up an interrupted radio
signal. The watch can take up to 15 minutes to synchronise with the radio signal. Once the radio
signal has been found the watch will show the time again.
4. Press the A button 3 times after the watch has resumed to normal running in order to check the
reception status.
If the reception / update was successful the watch will say “Country name” followed by “Time Updated”.
If the reception failed the watch will say”Country name” follow by “Time Not Updated”. If this happens
please try repeating the process again. If the repeated process is still unsuccessful then we suggest
you leave it on a window ledge or a place where it will pick up an interrupted radio signal and the watch
will then re-calibrate to the correct time at 03:00am the following day.
It is possible that having followed the manual and automatic Set Country instructions that the time is still
incorrect but when you press the A button (next to 2 o’clock) it says the correct time. Although this is not
correct as the time shown on the clock face is different to what the watch says the watch it is however
not broken or damaged. In order to re-correct this simply follow the steps below:
1. Unscrew (anti-clockwise) but do not pull out the stop / reset dial (in-between the A and B button).
The second hand must still be moving correctly.
2. Wait until the second hand stops at 12 o’clock exactly and immediately pull out the stop / reset dial
so that the second hand stops at 12 o’clock position.
3. Position the hour and minute hands using the stop / reset dial so the hour, minute and second
hands now all point to 12 o’clock.
4. Press and hold the A button (next to 2 o’clock) for 5 seconds and then push the stop / reset dial in.
5. The watch will now spin to match the internal time and resume normal running. Please wait until
the clock face resumes to the correct time. You can now press the A button, the time on the clock
face and the internal voice settings will be correct.
Set Daily Alarm (with automatic time settings)
1. Press the B button (next to 4 o’clock) while the watch is normal time mode for more than 5 seconds
until the watch says “Set Alarm, press 2 o’clock button to Set”.
2. Press the A button (next to 2 o’clock) until the watch says “Press 2 o’clock button to set hour, 4
o’clock button to confirm.”
3. Press the A button to set the alarm hour.
4. Press the B button after the alarm hour is set. The watch will now say “Press 2 o’clock button to set
minute, 4 o’clock button to confirm.”
5. Press the A button to set alarm minute, and then press the B button to confirm. After confirmation
the watch will tell the alarm time (hour and minute) that you have set.
6. To check your alarm time setting, press the B button (next to 4 o’clock) once to check alarm time
setting and if the alarm is set to ON or OFF (the watch will say the alarm time followed by “Alarm is
ON” or “Alarm is OFF”).
PLEASE NOTE:
•
The alarm will beep for 30 seconds you can turn off the alarm off by pressing either
the A or B buttons.
•
The alarm is a daily alarm, so even if you turned the beeping sound off, the alarm will beep the next
day again at the same time. If you want to turn off the Daily Alarm, you can follow the Alarm On/Off
setting as below.
•
Every time the beep goes off it will tell the “Alarm Time”.
ALARM ON/OFF:
1. Press the B button (next to 4 o’clock) while the watch is in the normal running mode for around 5
seconds until the watch says “set alarm, press 2 o’clock button to set.”
2. Press the B button one more time, the watch will say “alarm on/off, press 2 o’clock button to set”.
3. Press the A button (next to 2 o’clock) the watch will then say “press 2 o’clock button to on/
off 4 o’clock button to confirm.”
4. Press the A button.
5. Every press of the A button switches the alarm from ON to OFF. The watch will say, “alarm on”
when it is set to on or “alarm off” when it is set to off.
6. Press the B button to confirm and exit.
CHIME ON/OFF (Hourly Time Announcement)
(When the chime is on the watch announces the “HOUR” every hour)
1. Press and hold down the B button (next to 4 o’clock) while the watch is in the normal running mode
for around 5 seconds until the watch says “set alarm, press 2 o’clock button to set”.
2. Press the B button again 2 more times till the watch says “chime ON/OFF, 2 o’clock button to set”.
3. Press the A button (next to 2 o’clock) until the watch says “press 2 o’clock button to on/
off, 4 o’clock button to confirm.”
4. Press the A button again.
5. Every press of A button switches the hourly chime alert from ON to OFF. The watch will say, “chime
on” when it is set to on or “chime off” when it is set to off.
6. Press the B button to confirm and exit.
7. After the chime alert is confirmed to ON, the watch will announce “HOUR” every one hour.
SET DAILY ALARM (with manual signal settings)
Use this function only when you travel to countries with no radio signal. Your watch must be reset to
receive the radio signal when you return to the UK, Germany, USA or Japan from countries without
radio signal. If you don’t, the watch will not pick up a signal at 3am each morning.
everyday solutions
™
Est. 1992
