background image

ALSO

 IN 

THE R

ANGE

Vist 

lascarelectronics.com/data-loggers

 to see our 

full range of data loggers and measuring devices

AC

CESSORIES

INCLUDED

 IN 

THE BO

X

PSU

 

Power supply

3 x ADAPTORS

 

CABLE 

Power cable

EL-IOT  

WALL BRACKET 

Wall mounting bracket 

with magnets

BAT 1V5 AA PK4

4 x AA 1.5V  

alkaline batteries

EL-IOT-1 

WiFi Ambient temperature

data logger

EL-WEM 

WiFi Indoor Air Quality 

Monitor

EL-WEM+ 

WiFi High Accuracy Indoor 

Air Quality Monitor

EL-IOT-TC 

WiFi thermocouple  

temperature data logger

EL-IOT-TH+

WiFi High accuracy 

temperature and humidity 

data logger

EL-IOT-TH 

WiFi temperature and 

humidity data logger

www.lascarelectronics.com

Issue 1   06/2022

EL-IOT-CO2

Carbon Dioxide WiFi Cloud-Connected Data Logger

Your data, anytime, anywhere

Power Supply Voltage

9Vdc, 300mA

Operating Environment 

(power supply)

-20 to +60°C

5% to 85% RH, 

75kPa to 106kPa

Operating Environment 

(battery power)

-18 to +55°C

Transportation and 

Storage Environment

-20 to +60°C

Net Weight

243g

Recommended Wall 

Fixing Screws

3.5 x 20mm, countersunk head, 

cross recessed, stainless steel

BATTERY INFORMATION

This device is designed to be powered using the 
USB power supply provided. The logger does not 
lose its stored data readings when the power 
supply is disrupted. However, if the device has 
been logging, the logging process will stop 
and will not resume until the power supply is 
restored, and the device has reconnected to the 
WiFi network.

To provide a back-up source of power in case 
the mains supply is lost, you can fit four AA 
batteries and the product will automatically 
switch to using them when needed. Use only 
AA 1.5V alkaline batteries. We recommend you 
replace the batteries annually. When the  
EL-IOT-CO2 is in battery mode, fresh air  
calibration is not possible.

CALIBRATION CERTIFICATES

Lascar offers a Traceable Calibration Certificate 
Service for temperature and humidity sensors. 
Using reference equipment which has been 
calibrated by a UKAS/NIST accredited laboratory 
and using apparatus traceable to national or 
international standards. For more information 
please see www.lascarelectronics.com.

TECHNICAL INFORMATION

EL-IOT  

WALL BRACKET 

Wall mounting bracket

Summary of Contents for EL-IOT-CO2








Reviews: