background image

 

Introduction 

Thank you for purchasing the Easymount® Sign laminator.

 

This Easymount® Sign laminator is designed to perform and built to last. 

It’s

 an easy-to-use laminating 

system with self-gripping mandrels and a drop down feed tray [Excludes EM-S880].

 

The Easymount® Sign includes an integral media take-up unit, making the system ideal for single banners 

or reel-to-reel laminating up to 50m in length [Excludes EM-S880].

 

Mount prints on-to boards and apply 

vinyl’s

, tapes and adhesive films quickly and easily. Ideal for laminating 

single banners, reel-to-reel laminates [Excludes EM-S880], posters, graphics, signs, pop-up displays and 
many more.

 

Please read these instructions carefully before starting to use the system to ensure you get the best results 

and are competent at operation.

 

Should you experience any problems please contact your supplier for further information.

 

 

 

 

 

 

 

The EM-S880 model does not have a media mandrel, take up unit and the feed tray is fixed. 

Emergency stop 

Magic eye 
safety feature 

Self-gripping 
mandrels 

Pressure gauge 
handle 

Easy to use 
control panel 

Media mandrel 

[Excludes EM-S880]

 

Drop down feed tray 

[Excludes EM-S880]

 

 

Summary of Contents for EM-S880

















Reviews: