background image

To  turn  on  the  collar  receiver

,  short  press  the  power  button  three  times 

repeatedly within 3 seconds, a RED light will come up each time when the button is 
pressed down and go off when the button is released. The collar receiver will short 
bleep once. The collar receiver is now turned on into working mode. It will respond 
to the commands sent from the transmitter handset if it is matched up properly in 
the selected  dog channel. 

To  turn  off  the  collar  receiver

,  short  press  the  power  button  three  times 

repeatedly within 3 seconds, a GREEN light will come up each time when the button 
is pressed down and go off when the button is released. The collar receiver will emit 
a long beep once (for about 1 second). The collar receiver is now turned off into OFF 
mode. It will not receive any commands from the transmitter handset.  

To tell whether the collar receiver is ON or OFF

simply short press the power 

button once, if a green LED light comes up when the button is pressed, it means the 
collar receiver is in working mode (ON). If a red LED light comes up when the button 
is pressed, it means the collar receiver is in OFF mode (OFF).  

You can also tell from the length of the beep to see whether the collar receiver is ON 
or OFF. If the collar receiver gives a short beep when you are performing the turning 
ON/OFF  procedures  manually,  it  means  the  collar  receiver  is  turned  on.  If  collar 
receiver  gives  a  longer  beep  when  you  are  performing  the  turning  ON/OFF 
procedures manually,  it means the collar receiver is turned off. 

The average battery usage time for the collar receiver is about 3 to 5 days before it 
needs a recharge. This will also depend on how often and what type of correction is 
used on the collar receiver. 

To achieve longer battery life,

 please turn off the collar receiver when it is not used.  

If  the  system  is  not  going  to  be  used  for  a  long  period  of  time,  please  do  the 
following: 

1. Fully charge both transmitter handset and collar receiver; 

2. Switch both of them off properly; 

3. Store them in a still and cool place. 

 

 

 

Summary of Contents for EP-380R



















Reviews: