background image

 

1. Safety instructions 

1.1 UPS safety instructions 

●Before  applying  the  UPS  system,  Please  read  through  all  safety  information  and  operating  instructions 

carefully. It’s recommended to save this manual properly for future reading. 

●Do not install the UPS system near the water or in moist environments.   
●Do not install the UPS system where it would be exposed to direct sunlight or near the heater. 
●Place the UPS staying away from the wall for some distances, ensure enough space on each side of UPS, 
do not block ventilation holes in the UPS housing. Install it by following the instructions in the manual. 

●Please do not open the UPS case as you will, there is a high risk of electric shocks inside. 
●Do not connect to the equipment like hair dryer or electric heater, to ensure the safety for the UPS. 

●Do not use liquid extinguisher if there is a fire, a dry powder extinguisher is recommended. 

Attention: 

UPS has high voltage inside, for personal safety, please do not repair by yourself. If any questions, please 

contact local service center or dealer. 

1.2 Battery safety instructions 

●Battery life cycle will be shortened as environment temperature rise. Replacing battery periodically can help 
to keep UPS in normal state and assure backup time required. 
●Battery  replacement  should  be  done  by  authorized  technician.  If you want to replace the battery cable, 

please purchase it from our local service center or distributors to avoid fever and lighter which can cause 

fire from inadequate power capacity. 

●Batteries may cause electric shocks and have a high short-circuit current, for human being safety, please 
follow the specifications as below when replace the batteries: 

A. Remove wristwatches, rings and other metal objects 

B. Use only tools with insulated grips and handles 

C. Wear insulated shoes and gloves 

D. Do not put the metal tools or parts on the battery 

E. Before disconnecting the terminals on battery, please cut off all the loads to battery first. 

●Do not dispose of the batteries with fire so as to avoid explosion. 
●Don’t open the battery, electrolyte inside will do harm to eyes and skin. Please use plenty of clean water to 
wash if touching and go to see a doctor. 
●Do not connect the positive pole and negative pole directly, otherwise it cause electric shocks or will be on 
fire. 
●The  battery  circuit  is  not  isolated  from  the  input  voltage,  high  voltage  may  occur  between  the  battery 
terminals and ground, before touching, please verify no voltage is present.

 

2. Features 

2.1 Unpacking inspection

 

●Open  the  UPS package, please check the enclosed accessories including user manual, RS232 

communication cable, USB cable and CD-ROM.   

●Check the UPS if anything damaged in transport. If find something damaged or parts missing, do not power 

on, please turn to the carrier and dealer. 

●To determine whether this UPS is the model you want to buy. Check the model name showed both on the 

front panel and rear panel of UPS to confirm. 

Summary of Contents for EA906S































Reviews: