5 seconds) until the LED flashes twice. Continue with step 3.
CD, TAPE, TUNER
Press the Preselection key to get to the AUDIO-mode. Then choose the device you want
to adjust by pressing the Level key and keep it pressed (for about 5 seconds) until the
LED blinks twice. Continue with step 3.
AMPLIFIER
Press the Preselection key to get to the AUDIO-mode. Then choose the device you want
to adjust by pressing the level key and keep it pressed (for about 5 seconds) until the LED
blinks twice. Then press the Preselection key “TUNER” briefly to get to the AMPLIFIER-
mode. Continue with step 3.
3. Enter code 001 (code search) with the number keys. The LED blinks twice.
4.
Manual operation:
Keep pressing the Power/Standby-key for TV, SAT and AMPLIFIER,
the Stop-key for VCR, CD and TAPE or the Numberkey 2 for TUNER at short intervals,
until the device shows reaction.
Automatic operation:
Press the Power/Standby-key for TV, SAT and
AMPLIFIER, the Stop-key for VCR, CD and TAPE or the Numberkey 2 for TUNER, until
your device shows reaction. Every 1.5 seconds the TV code is continued automatically
and the appropriate standby command is sent.
5. When your easytip S7 has found the right code your device switches off and you can then
release the key.
Continue with step 5.
6. Now press the Level key again until the LED blinks twice. This shows you that your easy-
tip S7 has stored the appropriate code number.
Now check the function of your remote control. If your easytip S7 does not react to the
code number it has found, repeat steps 1 to 5 until you have found a optimal code num-
ber.
ATTENTION!
A new code search begins with the last code number found in the previous search. When the
end of the code list is reached the LED will blink three times. The search is then repeated
from the beginning. Please be patient. There may be many codes to search through before
the code for your equipment is found.
Changing the direction or the search:
It is possible, particularly in automatic search mode, to skip over the relevant code by mista-
ke. In this case, you can reverse the direction of the search for a maximum of 5 codes by
pressing the Vol-key.
ATTENTION!
After 5 codes the search direction changes back automatically. If you want, you can press
the Vol+ -key to change back to the original search direction.
Adjusting color, contrast, bass, treble,...
for your TV set
1. Press the Level key.
2. Briefly press the Shift-key.
3. Press the wanted key within 5 seconds.
Numberkey 1 = Brightness
Numberkey 2 = Color
Numberkey 3 = Contrast
Numberkey 4 = Treble
Numberkey 5 = Bass
Numberkey 6 = Balance
4. You can adjust your device by using keys Vol- and Vol+.
5. After the end of adjusting, wait for about 5 seconds until the keys get back their normal
function.
Querying the Code Numbers
You will need this function to query the code found by the automatic code search, so that
you can note it down in this operating manual.
1. Press the chosen Level key (TV, SAT, VCR, CD,...) until the LED blinks twice.
2. Now enter code 002 for query mode.
ATTENTION!
The first figure of the 3-digit cod must be entered within 5 seconds of the LED blinking twice.
Otherwise the LED will flash once and you will have to repeat the procedure from step 1.
3. Now press key 1 and count the number of times the LED blinks. (For example, if the LED
blinks twice the first number in your code is 2).
Now press key 2 and count the times the times the LED blinks. (For example, if the LED
does not blink, the second number in your code is 0).
4
