background image

 

Dear Music Lover, 

Welcome! Congratulations on your purchase of our EAT C-Sharp turntable. Your EAT C-Sharp 

was hand-crafted by our team of skilled technicians. It has been tested rigorously and is 

ready for your enjoyment. 

Please take the time to read this manual carefully to ensure that you obtain the ultimate 

performance from your EAT C-Sharp turntable. The tips contained within will ensure that 

your C-Sharp will remain as-new condition for many years to come! 

 

Your contribution to enviromental protection. 

Disposal od packaging material: 

Packaging protects the device from damage during the transportation. The packaging 

materials were chosen with the regards to the enviromental protection and they are 

therefore recyclable. 

 

Disposal of old equipment: 

For the disposal of old equipment use a junk place appointed for that purpose. 

 

The device is shipped partially disassembled in order to avoid damage to sensitive parts. 

Please, double-check immediately after receiving it if the packaging and the device were not 

damage during the transportation. 

If damaged please do not operate. 

 

 

Warning of a hazard for the user, the unit or possible misuse. 

 

 

!

Summary of Contents for C-Sharp




















Reviews: