59
EL ................ Electronic Proportional Control 12 Vdc and
Electronic Driver with +/- 100 mA Command
Input
EM ............... Electronic Proportional Control 24 Vdc and
Electronic Driver with +/- 100 mA Command
Input
HA ............... Hydraulic Remote Control with 5-15 bar control
range
MA ............... Manual Displacement Control
MB ............... Manual Displacement Control (up to 24 Vdc)
Normally Closed Neutral Lockout
MC ............... Manual Displacement Control with Neutral Detent
ML ............... Manual Displacement Control w/Wide Band
Neutral.
Position 20* Control Orifice Supply (P)
Position 21* Control Orifice Servo (S
1
)
Position 22* Control Orifice Servo (S
2
)
0 .................. None
A .................. 0,53 [.021] Diameter
B .................. 0,71 [.028] Diameter
C .................. 0,91 [.036] Diameter
D .................. 1,12 [.044] Diameter
E .................. 1,22 [.048] Diameter
F .................. 1,32 [.052] Diameter
G .................. 1,45 [.057] Diameter
H .................. 1,65 [.065] Diameter
J .................. 1,85 [.073] Diameter
K .................. 2,06 [.081] Diameter
L .................. 2,39 [.094] Diameter
M ................. 2,59 [.102] Diameter
* Eaton recommends you chose an orifice for control orifice
supply (P). The servo orifice (S
1
) and the servo orifice (S
2
)
are optional, except when specifying a pressure override.
Position 23 Control Special Features
0 .................. No Control Special Features
3 .................. Destroke valve
Position 24 Charge Pump Displacement
0 .................. None
1 .................. 13,9 cm
3
/r [0.85 in
3
/r]
(Pump Disp. 54-89 cm
3
/rev)
2 .................. 17,4 cm
3
/r [1.06 in
3
/r]
(Pump Disp. 54-105 cm
3
/rev
Std for 105)
3 .................. 21,0 cm
3
/r [1.28 in
3
/r]
(Pump Disp. 54-105 cm
3
/rev)
4 .................. 27,9 cm
3
/r [1.70 in
3
/r]
(Pump Disp. 54-105 cm
3
/rev)
5 .................. 34,7 cm
3
/r [2.12 in
3
/r]
(Pump Disp. 89-105 cm
3
/rev)
Position 25 Auxiliary Mounting
0 .................. None, High Speed Charge Pump (Models 54 to 75
cm
3
/rev)
1 .................. None, High Torque Charge Pump (Models 54 to 105
cm
3
/rev)
A .................. A-pad, High Speed Charge Pump, Dual 2 Bolt
Mount, No Shaft Seal, 9 Tooth 16/32 Pitch Spline
(Available For 54-75 cm
3
/rev Only)
B .................. B-pad, High Speed Charge Pump, Dual 2 Bolt
Mount, No Shaft Seal, 13 Tooth 16/32 Pitch Spline
(Available For 54-75 cm
3
/rev Only)
C .................. A-pad, High Torque Charge Pump, Dual 2 Bolt
Mount, No Shaft Seal, 9 Tooth 16/32 Pitch Spline
(Available For All Models)
D .................. B-pad, High Torque Charge Pump, Dual 2 Bolt
Mount, No Shaft Seal, 13 Tooth 16/32 Pitch Spline
(Available For All Models)
E .................. B-B-pad, High Torque Charge Pump, Dual 2 Bolt
Mount, No Shaft Seal, 15 Tooth 16/32 Pitch Spline
(Available For All Models)
F .................. C-pad, High Torque Charge Pump, 4 Bolt Mount, No
Shaft Seal, 14 Tooth 12/24 Pitch Spline (Available
For All Models)
Position 26 Charge Pump Options
0 .................. None
A .................. Remote Pressure Side Filter Ports
Position 27 Charge Pressure Relief Valve Setting
0 .................. None
A .................. 21 bar [304.5 lbf/in
2
] - Standard
B .................. 22,5 bar [326.3 lbf/in
2
]
C .................. 24 bar [348 lbf/in
2
]
D .................. 25,5 bar [369.8 lbf/in
2
]
E .................. 27 bar [391.5 lbf/in
2
]
F .................. 28,5 bar [413.3 lbf/in
2
]
G .................. 30 bar [435 lbf/in
2
]
Position 28 Charge Pump Special Features
0 .................. No Charge Pump Special Features
Position 29 Paint and Packaging
0 .................. Painted Primer Blue (Standard)
Position 30 Identification On Unit
0 .................. Standard
Position 31 Design Code
A .................. A
