Eaton 200 A Fused Loadbreak Elbow Connector Replacement... Installation Instructions Manual Download

Page: 8 / 16

200 A Fused Loadbreak Elbow Connector Replacement Fuse

InstallatIon InstructIons

MN132021EN November 2016

Fuse Disassembly

Step 6

Gripping the square portion of the cable housing, and

keeping the cable housing stationary, apply a twist-and-pull

motion to the elbow housing to separate it from the cable

housing.

ote:

A screwdriver through the pulling eye on top of the

elbow will aid in twisting and pulling to separate.

Discard bleeder strap after housings are separated.

Elbow Housing

Upper

Pulling

Eye

Cable

Housing

Grip While

Separating

Facing

Outward

Separate

Step 7

Using the supplied 1/8

hex wrench, unthread the two set

screws from the probe adapter.

1/8" Hex Wrench

Summary of Contents for 200 A Fused Loadbreak Elbow Connector Replacement...

















Search results

Summary of Contents for 200 A Fused Loadbreak Elbow Connector Replacement...

Reviews:

Related manuals for 200 A Fused Loadbreak Elbow Connector Replacement...

Brands by name

Popular brands

Eaton 200 A Fused Loadbreak Elbow Connector Replacement..., Installation Instructions Manual

Search results

Summary of Contents for 200 A Fused Loadbreak Elbow Connector Replacement...

Reviews:

Related manuals for 200 A Fused Loadbreak Elbow Connector Replacement...

Brands by name

Popular brands