Eaton 5S 1000, Installation And User Manual

5

614-06822-00

1. Operating conditions

•   This product is an 

U

ninterruptible

 P

ower 

S

upply (

UPS

) for computers and their peripherals, television sets, stereo 

systems and video recorders... It must not be used to supply other electrical equipment (lighting, heating, household 

appliances, etc.).

2. UPS connections

•   Connect  the

 UPS 

1

 to the AC-power system via a wall outlet with an earth connector, using the input cord of your 

computer (see figure A).

•   Plug critical equipment (computer, monitor, modem, etc.) into the outlets 

9

 providing battery backup power and surge 

protection (see figure C), taking care not to exceed the rated current indicated in amperes.

•   Other devices (printer, scanner, fax, etc.) can be connect to the surge protection outlets 

8

 (see figure C). The surge 

protection outlets are not backed up by battery power in the event of a power outage.

•   Optional Internet modem / Network connection:

A modem or Ethernet data line can be protected against surges by connecting it via the 

UPS

. Connect the existing device 

cable between the wall outlet and the 

UPS

, and use a similar cable between the 

UPS

 and the device, as indicated in  

figure B (cable not supplied).

• 

 Optional USB connection:

The 

UPS

 device can be connected to the computer using the USB cable 

4

 supplied (see figure B). 

Eaton UPS Companion software is downloadable from powerquality.eaton.com.  

Register for the warranty on powerquality.eaton.com. 

3. Operation

•   

Battery charge: 

The 

UPS

 charges the battery as soon as it is connected to the AC outlet, whether button 

12

 is pressed or 

not. When used for the first time, the battery will only provide its maximum performance after it has been charged for 8 

hours. It is recommended that the 

UPS

 be permanently connected to the AC power supply to ensure the best possible 

performance.

• 

Switching-on the UPS

: press button 

12

 for about 1 second.

•   

Surge protection outlets

8

without battery backup: 

Equipment connected to these outlets is supplied as soon as the 

input AC cord is plugged in. They are not affected by button 

12

.

• 

 Battery backup outlets

9

:

 Equipment connected to these outlets is supplied as soon as button 

12

 turns green  

(see figure D). These outlets can be turned on even if the 

UPS

 is not connected to AC power (button 

12

 flashes).

•   

AC-power disturbance: 

If AC power is disturbed or fails, the 

UPS

 continues to operate on battery power. Button 

12

 flashes 

green. In normal mode, the audible alarm beeps every ten seconds, then every three seconds when the end of battery 

backup time is near. In silent mode, the audible alarm simply beeps once when the 

UPS 

transfers to battery power.

•   If the power outage lasts longer than the battery backup time, the

 UPS

 shuts down and automatically restarts when 

power is restored. Following a complete discharge, a few hours are required to recharge the battery back to full backup 

time.

• 

 Surge protection:

 All outlets include surge protection.

• 

Shutdown of the battery backup outlets 

9

: 

Press button 

12

 for more than two seconds.

8

 : Surge protection outlets.

9

 :  Battery backup outlets.

11

 :  LED ON indicate a UPS fault.

12

 :  ON/OFF button for the battery backup 

outlets.

13

 :  Protection (circuit breaker).

Troubleshooting (For further information, visit the www.powerquality.eaton.com site or contact after-sales support.)

Problem

Diagnostic

Solution

1

•  The battery backup outlets 

9

 are not 

supplied with power.

•  Button 

12

 is not lighted on.

•  Press button 

12

 and check that it turns 

green.

2

•  The connected devices are not 

supplied when AC power fails.

•  The devices are not connected to the 

battery backup outlets 

9

.

•  Connect the devices to the battery 

backup outlets 

9

.

3

•  AC power is available, but the 

UPS

operates on battery power.

•  Circuit breaker 

13

, located at the rear 

of the 

UPS

, has been tripped by an 

overload on the 

UPS

 output.

•  Disconnect excess equipment and 

reset the circuit breaker 

13

 by pressing 

the corresponding button.

4

•  Green button 

12

 and red LED 

11

 are 

on and audible alarm beeps every 2 

seconds.

•  The 

UPS

 battery backup outlets 

9

are overloaded.

•  Disconnect excess equipment 

connected to the battery backup outlets 

9

.

5

•  Red LED 

11

 is on and the audible 

alarm beeps continuously.

•  A fault has occurred on the 

UPS

. The 

battery backup outlets 

9

 are no longer 

supplied.

•  Call after-sales support.

ENGLISH

12

13

8

8

11

9

13

9

13

9

8