background image

Eaton 9315/9390/9395/9395P Fixed Primary Sync Control Installation and Operation Manual    P-164000023—Rev 03    

2-1

Chapter 2

Installation Plan and Unpacking

The Eaton Fixed Primary Sync Control is shipped as a separate item and can be mounted on any surface that 
can safely bear its weight. See paragraph 2.2 for weight, dimensions, and wiring preparation.

2.1

Creating an Installation Plan

Before installing the UPS system, read and understand how this manual applies to the system being installed. 
Use the procedures and illustrations in paragraph 3.2 and Chapter 4 to create a logical plan for installing the 

system.

2.2

Preparing the Site

For the Eaton Fixed Primary Sync Control to operate at peak efficiency, the installation site should meet the 
environmental parameters outlined in the applicable Eaton 9315, Eaton 9390, Power Xpert 9395, or Power 
Xpert 9395 High Performance (Power Xpert 9395P) UPS installation and operation manual listed in paragraph 
1.3.

2.2.1

Environmental and Installation Considerations

The life of the Eaton Fixed Primary Sync Control is adversely affected if the system is not installed in a 
temperature and humidity controlled indoor area free of conductive contaminants.

Failure to follow guidelines may void your warranty.The UPS equipment operating environment must meet the 
weight requirements shown in Table 2-1 and the size requirements shown in Figure 2-1 and Figure 2-2. 
Dimensions are in millimeters (inches).

NOTE

Startup and operational checks must be performed by an authorized Eaton 
Customer Service Engineer, or the warranty terms specified on page W1 become 
void. This service is offered as part of the sales contract for the UPS. Contact an 
Eaton service representative in advance (usually a twoweek notice is required) to 
reserve a preferred startup date.

Table 2-1. Equipment Weight

Model

Weight

kg (lb)

Shipping

Installed

Eaton Fixed Primary Sync Control

45.4 (100)

36.3 (80)

Eaton Primary Interface

17.25 (38)

15.0 (33)

Summary of Contents for 9315P































































Reviews: