Eaton 9355 Parallel UPS (10/15 kVA) User's Guide 164201601—Rev E0
49
C
Chhaapptteerr 66 O
Oppeerraattiioonn
This chapter contains information on how to use the Eaton 9355 UPS, including front panel operation, UPS
startup and shutdown, and configuring the UPS for Extended Battery Modules (EBMs).
66..11
C
Coonnttrrooll P
Paanneell FFuunnccttiioonnss
The UPS has a four-button graphical LCD with backlight. It provides useful information about the UPS itself,
load status, events, measurements, and settings (see
).
Figure 45. Eaton 9355 UPS Control Panel
Power On Indicator (green)
On Battery Indicator (yellow)
Bypass Indicator (yellow)
Alarm Indicator (red)
Control Buttons
for the LCD Menu Options
The following table shows the indicator status and description.
Indicator
Status
Description
CORD KIT INSTRUCTIONS
Eaton BladeUPS Cord Kit Instructions
S
164201721 Rev 2
Draft 13-APR-2010
5
Removing the Existing Power Cords
To remove the existing power cords:
1.
If the UPS and internal batteries are already installed, continue to
Step 2. If the UPS and internal batteries are not installed, continue
to Step 15.
2.
You MUST shut down the UPS before replacing the cord assembly.
Continue to Step 3 to shut down a standalone UPS.
For parallel shutdown procedures, refer to the
Eaton BladeUPS
(12 kVA) User's Guide
and then continue to Step 11.
3.
Switch the load connector circuit breaker to the OFF (O) position
(see Figure 2).
NOTE
The load connector breaker controls the load connector only, not the output power.
4.
Press any button on the front panel display to activate the menu
options. Select TURN UPS ON/OFF, TURN UPS OFF, and press the
button.
5.
Confirm the selection. Press and hold the
button for three
seconds, until the UPS stops beeping.
The output relays open, the UPS transfers to Standby mode, and
the
indicator turns off.
6.
Switch the UPS battery circuit breaker to the OFF (O) position.
7.
If optional EBMs are installed, switch all EBM battery circuit
breakers to the OFF (O) position.
Disconnect the EBM cable from the UPS extended battery
connector.
8.
Switch the UPS input circuit breaker to the OFF (O) position.
9.
Switch off utility power where the UPS is connected.
10.
Unplug the power cords.
Green
On
The UPS is operating normally.
Flashing
A new information message is active.
Off
The UPS is turned off and will not turn on automatically.
OPERATION
Eaton 9355 Parallel UPS (10/15 kVA) User's Guide
S
164201601 Rev B
56
The following table shows the indicator status and description.
Indicator
Status
Description
Green
On
The UPS is operating normally.
Flashing
S
The UPS is starting up or is shut down and waiting for power to return.
S
A new information message is active.
S
Bypass is not available.
Off
The UPS is turned off and will not turn on automatically.
Yellow
On
The UPS is in Battery mode.
Yellow
On
The UPS is in Bypass mode.
Red
On
The UPS has an active alarm.
Flashing
There is a new UPS alarm condition. See “Troubleshooting” on page 67 for
additional information.
Changing the Language
Press and hold the first button on the left for approximately five seconds
to select the language menu. This action is possible from any LCD menu
screen.
Display Functions
As the default or after 15 minutes of inactivity, the LCD displays the
selectable startup screen. The default is the Eaton logo and can be
changed to the Mimic screen in the User Settings menu.
The backlit LCD automatically dims after a long period of inactivity. Press
any button to restore the screen.
Use the two middle buttons ( and ) to scroll through the menu
structure. Press the
button to enter a submenu. Press the
button
to select an option. Press the
ESC
button to cancel or return to the
previous menu.
Yellow
On
The UPS is in Battery mode.
OPERATION
Eaton 9355 Parallel UPS (10/15 kVA) User's Guide
S
164201601 Rev B
56
The following table shows the indicator status and description.
Indicator
Status
Description
Green
On
The UPS is operating normally.
Flashing
S
The UPS is starting up or is shut down and waiting for power to return.
S
A new information message is active.
S
Bypass is not available.
Off
The UPS is turned off and will not turn on automatically.
Yellow
On
The UPS is in Battery mode.
Yellow
On
The UPS is in Bypass mode.
Red
On
The UPS has an active alarm.
Flashing
There is a new UPS alarm condition. See “Troubleshooting” on page 67 for
additional information.
Changing the Language
Press and hold the first button on the left for approximately five seconds
to select the language menu. This action is possible from any LCD menu
screen.
Display Functions
As the default or after 15 minutes of inactivity, the LCD displays the
selectable startup screen. The default is the Eaton logo and can be
changed to the Mimic screen in the User Settings menu.
The backlit LCD automatically dims after a long period of inactivity. Press
any button to restore the screen.
Use the two middle buttons ( and ) to scroll through the menu
structure. Press the
button to enter a submenu. Press the
button
to select an option. Press the
ESC
button to cancel or return to the
previous menu.
Yellow
On
The UPS is in Bypass mode.
OPERATION
Eaton 9355 Parallel UPS (10/15 kVA) User's Guide
S
164201601 Rev B
56
The following table shows the indicator status and description.
Indicator
Status
Description
Green
On
The UPS is operating normally.
Flashing
S
The UPS is starting up or is shut down and waiting for power to return.
S
A new information message is active.
S
Bypass is not available.
Off
The UPS is turned off and will not turn on automatically.
Yellow
On
The UPS is in Battery mode.
Yellow
On
The UPS is in Bypass mode.
Red
On
The UPS has an active alarm.
Flashing
There is a new UPS alarm condition. See “Troubleshooting” on page 67 for
additional information.
Changing the Language
Press and hold the first button on the left for approximately five seconds
to select the language menu. This action is possible from any LCD menu
screen.
Display Functions
As the default or after 15 minutes of inactivity, the LCD displays the
selectable startup screen. The default is the Eaton logo and can be
changed to the Mimic screen in the User Settings menu.
The backlit LCD automatically dims after a long period of inactivity. Press
any button to restore the screen.
Use the two middle buttons ( and ) to scroll through the menu
structure. Press the
button to enter a submenu. Press the
button
to select an option. Press the
ESC
button to cancel or return to the
previous menu.
Red
On
The UPS has an active alarm.
Flashing
There is a new UPS alarm condition. See
for additional
information.
66..11..11
C
Chhaannggiinngg tthhee LLaanngguuaaggee
Press and hold the first button on the left for approximately five seconds to select the language menu. This
action is possible from any LCD menu screen.
66..11..22
D
Diissppllaayy FFuunnccttiioonnss
As the default or after 15 minutes of inactivity, the LCD displays the selectable startup screen. The default is
the Eaton logo and can be changed to the Mimic screen in the User Settings menu.
Summary of Contents for 9355 Series
