background image

 
P-164000427 

SMALL and LARGE BATTERY CABINET 

10 

Revision 2 

User's and Installation Guide 

2.2 Preparing the Large Battery Cabinet installation 

 

 

 

NOTE

 

 

 

The  battery cabinet is  heavy. If unpacking instructions  are  not  closely followed, the 
cabinet may  tip  and  cause  serious  injury. 

 

 

 

1. 

If not  already  accomplished, use  a  forklift or  other material handling  equipment to  move the 
cabinet to  the  installation area, or as close as possible, before unloading from the pallet. Insert 
the forklift jacks between the skids on the bottom of the unit. 

2. 

Open the package and remove the two front mounting brackets on the side feet and 
two rear mounting bolts inside the middle foot. 
 

3. 

Carefully lift the battery cabinet off the pallet. Now the battery cabinet is ready to be 
placed aside the UPS.  
Notes of installation location with 

93PM UPS

 

Both sides can be used for battery cabinet placement but for easier service access 
to UPS, on the 93PM 30-150 kW UPS right side is preferred, and on the 93PM 
160-200 kW left side is preferred. 

 

The battery cabinet must be located on the right side of 93PM 30 -50 kW UPS 
cabinet if wiring through cabinet side panels. The 93PM 160 -200 kW UPS does not 
enable wiring through its side panel. 

Notes of installation location with 

93E UPS

 

Both sides can be used for battery cabinet placement with the 93E UPS but on the 
left side is preferred with the 80-120 kVA UPS, and on the right side is preferred 
with the 160-200 kVA UPS to more easily access the battery input terminals 
through the bottom or the rear entry. 

 

4. 

Open  the  battery  cabinet  and  locate  the  signal  wiring  shipped  along  the  cabinet.  The 
power  cable  must  be  made  according  to  installation  requirements.  Minimum  cross-
section area for copper cable is stated on the next table: 

T able 2-2: Cable cross -section minimum areas  

UPS power 

rating 

(kW) 

Min Cu cable size 

(mm2) 

 

+ and - 

PE 

30 - 50 

50 

25 

60 - 80 

70 

35 

90 - 100 

95 

50 

110 - 150 

2 x 70 

70 

160 - 200 

2 x 95 

95 

 
 

 

Summary of Contents for 93E



























Reviews: