background image

 
P-164000427 

SMALL and LARGE BATTERY CABINET 

19 

Revision 2 

User's and Installation Guide 

5 Warranty 

 

The  product is  warranted against defects  in materials and  workmanship for a period  of twelve 
(12) months from  its  original date of purchase. The  local office  or distributor may  grant  a  warranty 
period different to  the  above. Please refer  to  local terms of liability as  defined in the  supply 
contract. 

 

The  UPS  manufacturer is not  responsible  for 

 

 

Any  costs  resulting  from  a  failure  if  the  installation,  commissioning,  repair,  alternation,  or 
ambient  conditions  of  the  equipment  do  not  fulfil  the  requirements  specified  in  the 
documentation  delivered with  the  unit  and  other relevant documentation. 

 

Equipment subjected to  misuse, negligence or accident. 

 

Equipment comprised of materials provided or designs stipulated by the  purchaser. 

 
The  warranty is only  valid if the  installation inspection and  initial start-up  of the  UPS  unit  is 
carried out  by a service engineer approved by  Eaton. Service and  maintenance of the  UPS 
shall  also  be performed only by a service engineer approved by  Eaton. Otherwise the 
warranty will be  voided. 

 

If the  product fails to  meet its  published specifications due  to  a  defect in material and 
workmanship, covered by  this  warranty, the  seller  will repair  or replace the  warranted product. 
Such  repair  or replacement will be  made by  Eaton  or by  a service provider  approved by Eaton. 
Repair  or replacement during  the  warranty period  does not  extend the  original warranty. Warranty 
does not  cover taxes, which will be  due  in connection with  replacement or repair  of the  product. 

 

Batteries are  warranted against failures  in material and  workmanship, not  against the  normal  aging 
and  reduction of ampere-hour capacity. The  product storage environment has  to  meet 
manufacturer's specifications, failure  to  do  this  will cause the  warranty to  be  voided. 

 

Under  no  circumstances shall  the  manufacturer, its  suppliers or  subcontractors be  liable for 
special, indirect, incidental or consequential damages, losses  or penalties. 

 

The  technical data, information and  specifications are  valid at  the  time  of printing.  The  UPS 
manufacturer reserves  the  right  to  modifications without prior notice. 

 

 

 

Summary of Contents for 93E



























Reviews: