background image

 

 

 

PUB 50411

 

 

D64RP18 SERIES B1 DIGITAL GROUND FAULT RELAY 

 

 

Revision 2 

May, 2005 

Page 2 

 

 

 

TABLE OF CONTENTS 

 

 

 

PAGE 

 

TABLE OF CONTENTS

  .........................................................................................................................  

 

LIST OF TABLES, FIGURES & FORMS

..................................................................................................  

 

1.

 

GENERAL DESCRIPTION

..........................................................................................................  

 

2.

 

OPERATION

 

.........................................................................................................................  

 

 

2.1 

GLOSSARY OF TERMS................................................................................................  

 

2.2

 

DIP

SWITCH SETTINGS................................................................................................  

 

 

2.2.1 

GROUND FAULT TRIP CURRENT LEVEL .....................................................  

 

 

2.2.2 

GROUND FAULT TRIP DELAY TIME .............................................................  

 

2.3 

OUTPUT RELAY OPERATING MODE..........................................................................  

 

2.4 

OUTPUT RELAY CONTACT STATE.............................................................................  

 

2.5 

INDICATION ..................................................................................................................  

 

2.6 

RESET  .........................................................................................................................  

 

2.7 

GROUND FAULT TEST.................................................................................................  

3.

 

INSTALLATION INSTRUCTIONS

..............................................................................................  

 

3.1 

MOUNTING....................................................................................................................  

 

3.2 

BUILT-IN CURRENT TRANSFORMER.........................................................................  

 

3.3 

EXTERNAL CURRENT TRANSFORMER.....................................................................  

 

3.4 

CONNECTIONS ............................................................................................................  

 

 

3.4.1 

CONNECTING MORE THAN ONE D64RP18 TO REMOTE TEST/RESET....  

4.

 

CATALOG NUMBERS

................................................................................................................  

5.

 

TECHNICAL SPECIFICATIONS

.................................................................................................   10 

 

 

LIST OF TABLES, FIGURES & FORMS

 

TABLE NO.

                                                   

PAGE   

1. 

DIPSWITCH SETTINGS .............................................................................................................  

2. 

OUTPUT RELAY CONTACT STATES........................................................................................   13 

 
FIGURE NO.

 

1. 

TYPICAL FIELD CONNECTION WITH BUILT-IN CT .................................................................   14 

2. 

TYPICAL FIELD CONNECTION WITH 500:1 INTERPOSING CT..............................................   15 

3. 

DIMENSIONS AND WEIGHTS 

D64RP18

 RELAY....................................................................   16 

 

FORM NO. 

1. 

TEST RECORD  .........................................................................................................................   17

 

Summary of Contents for Cutler-Hammer D64RP18


















Reviews: