Eaton Cutler-Hammer D64RPB100 Series Instruction Manual Download

Page: 16 / 26

PUB 50412

D64RPB100 SERIES B1 DIGITAL GROUND FAULT RELAY

Revision 3

April, 2008

Page 16

Ground Fault Trip Current Level

30 mA - 9000 Amps in three ranges

Sensing Ranges Vs Trip Current Level Settings:

10 mA – 10 Amp with built-in CT .......................................................... 30 mA – 9 Amp

10 mA – 10 Amp with 500:1 external CT on terminals T1 & T2 ............ 30 mA – 9 Amp

1 - 1000 Amp with 500:5 interposing CT ....................................................3 – 900 Amp

10 - 10000 Amp with 5000:5 interposing CT ..........................................30 – 9000 Amp

Selection of each Range ...........................DIPswitch 1 on front of relay and interposing CT

Setting within each Range.....................................DIPswitches 2, 3, 4, & 5 on front of relay

Trip Current Accuracy ....................................................................+0%, -15% of trip setting

Note: The accuracy of the trip point refers to the value of the real world current

(assuming a purely sinusoidal wave shape) that just causes a trip, with

respect to the specified value in the table.

Frequency Response Range .....................................................................................45 - 450 Hz

Thermal Characteristics:

Short Time Withstand:

1000A ...............................................................................................................1 second

2000A ............................................................................................................0.1 second

Environment:

Operating Temperature.................................................................................-20

C to +50

Storage..........................................................................................................-40

C to +80

Humidity ..........................................................................................85% (No Condensation)

Shock resistance.............................................................................................. 10G (no malfunction)

Vibration resistance............................ 10G, 10-55 Hz at 1.5 mm double amplitude (no malfunction)

Ingress protection........................................................................................................................IP20

Dimensions (refer to Figure 4):

Height............................................................................................................. 2.76" (70 mm)

Width............................................................................................................ 3.94" (100 mm)

Depth (not including terminal blocks) ........................................................... 4.02" (102 mm)

Depth (including terminal blocks) ................................................................. 4.85" (123 mm)

Mounting (refer to Figure 4):

DIN rail ....................................................................................................................... 35 mm

Two Screw........................................................................................#8 x 3/4" (M4 x 20 mm)

Weight:

Open......................................................................................................... 1.88 lbs. (0.85 kg)

Packaged ................................................................................................. 2.43 lbs. (1.10 kg)

Summary of Contents for Cutler-Hammer D64RPB100 Series



























Search results

Summary of Contents for Cutler-Hammer D64RPB100 Series

Reviews:

Related manuals for Cutler-Hammer D64RPB100 Series

Brands by name

Popular brands

Eaton Cutler-Hammer D64RPB100 Series, Instruction Manual

Search results

Summary of Contents for Cutler-Hammer D64RPB100 Series

Reviews:

Related manuals for Cutler-Hammer D64RPB100 Series

Brands by name

Popular brands