Page 1-1
IL17569
Effective June, 2001
1
PRODUCT OVERVIEW
1.1 General Description
The FP-5000 Protective Relay is a multi-function panel mounted,
microprocessor-based relay, designed for both ANSI and IEC
applications (Figure
1-1
). It is a self-contained device which
operates from either AC or DC control power and provides true rms
sensing of each phase and ground current. Only one relay is
required per 3-phase circuit. Current, voltage, and operator-
selectable protective functions are integral to each device.
The FP-5000 is designed to protect the mains, ties or feeders at any
voltage level. It is primarily applied on medium voltage
distribution circuits up to 69 kV. The FP-5000 monitors several
primary and derived electrical parameters of the system.
1.2 Audience
The audience for this document is the Specifying or System
Engineer, the operating personnel, and the troubleshooting
personnel. This document will guide the system user to apply and
program the FP-5000. The document will provide operating
information, enabling the operating user to start and trip the breaker
associated with the FP-5000. The operator can refer to this
publication regarding any operation of the FP-5000. This document
will also provide information to program the FP-5000 and use the
troubleshooting features to collect and analyze historical, trending
and oscillographic data.
1.3 Safety and Caution Notices/Disclaimers
This technical document is intended to cover most aspects
associated with the installation, application, operation and mainte-
nance of the Cutler-Hammer FP-5000 Protective Relay. It is
provided as a guide for authorized and qualified personnel only in
the selection and application of the FP-5000 Protective Relay. Please
refer to the specific
WARNING
and
CAUTION
below before proceed-
ing. If further information is required by the purchaser regarding a
particular installation, application or maintenance activity, a Cutler-
Hammer representative should be contacted. Technical Support is
available 24 hours a day by phoning Cutler-Hammer Power Manage-
ment Applications Support at 1-800-809-2772, Option 1.
See also 12.3, Getting help from Cutler-Hammer.
1.3.1 WARRANTY AND LIABILITY INFORMATION
CAUTION
NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OF
MERCHANTABILITY, OR WARRANTIES ARISING FROM
COURSE OF DEALING OR USAGE OF TRADE, ARE MADE
REGARDING THE INFORMATION, RECOMMENDATIONS AND
DESCRIPTIONS CONTAINED HEREIN.
CAUTION
IN NO EVENT WILL CUTLER-HAMMER BE RESPONSIBLE TO
THE PURCHASER OR USER IN CONTRACT, IN TORT (INCLUD-
ING NEGLIGENCE), STRICT LIABILITY OR OTHERWISE FOR
ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGE OR LOSS WHATSOEVER, INCLUDING BUT NOT
LIMITED TO DAMAGE OR LOSS OF USE OF EQUIPMENT,
PLANT OR POWER SYSTEM, COST OF CAPITAL, LOSS OF
POWER, ADDITIONAL EXPENSES IN THE USE OF EXISTING
POWER FACILITIES, OR CLAIMS AGAINST THE PURCHASER
OR USER BY ITS CUSTOMERS RESULTING FROM THE USE OF
THE INFORMATION AND DESCRIPTIONS CONTAINED HEREIN.
CAUTION
ALL SAFETY CODES, SAFETY STANDARDS AND/OR REGULA-
TIONS MUST BE STRICTLY OBSERVED IN THE INSTALLATION,
OPERATION AND MAINTENANCE OF THIS DEVICE.
WARNING
THE WARNINGS AND CAUTIONS INCLUDED AS PART OF THE
PROCEDURAL STEPS IN THIS DOCUMENT ARE FOR PERSON-
NEL SAFETY AND PROTECTION OF EQUIPMENT FROM
DAMAGE. AN EXAMPLE OF A TYPICAL WARNING LABEL
HEADING IS SHOWN ABOVE TO FAMILIARIZE
PERSONNEL
WITH THE STYLE OF PRESENTATION. THIS WILL HELP TO
ENSURE THAT PERSONNEL ARE ALERT TO WARNINGS,
WHICH MAY APPEAR THROUGHOUT THE DOCUMENT. IN
ADDITION, CAUTIONS ARE ALL UPPERCASE AND BOLDFACE.
CAUTION
COMPLETELY READ AND UNDERSTAND THE MATERIAL
PRESENTED IN THIS DOCUMENT BEFORE ATTEMPTING
INSTALLATION, OPERATION OR APPLICATION OF THE
EQUIPMENT. IN ADDITION, ONLY QUALIFIED PERSONS
SHOULD BE PERMITTED TO PERFORM ANY WORK ASSOCI-
ATED WITH THE EQUIPMENT. ANY WIRING INSTRUCTIONS
PRESENTED IN THIS DOCUMENT MUST BE FOLLOWED
PRECISELY. FAILURE TO DO SO COULD CAUSE PERMANENT
EQUIPMENT DAMAGE.
WARNING
THE LOSS OF CONTROL VOLTAGE WILL CAUSE THE FP-5000
TO BE INOPERATIVE. IF AC CONTROL VOLTAGE IS USED, AN
APPROPRIATE RELIABLE POWER SOURCE/SCHEME SHOULD
BE SELECTED (POSSIBLY A UPS SYSTEM) TO SUPPLY
POWER TO THE RELAY.
Summary of Contents for Cutler-Hammer FP-5000
