background image

I.L. 17403

Page 9

Effective 9/04

Interposing Relay

START

STOP

3

2

LOW VOLTAGE RELEASE WITH

TWO-WIRE PUSHBUTTON

 START-STOP OPERATION

Fig. 11   Two-Wire Control

Fig. 12    Two-Wire Control with IMPACC

TWO-WIRE CONTROL

Wire as shown in Figure 11 or 12. Install a #16 or #18

AWG stranded wire jumper from 3 to P. Keep strip length

to not more than 1/4 inch. 

Be sure to have jumper clear

power terminal.

 Attach and route twisted pair or shielded

wires to a remote reset/trip indicator module where pro-

vided.

Without Communications

Wire control devices in the same manner as conventional

motor controllers. Add the jumper.

With Communications

Attach a WPONI communications module and connect it

to the INCOM network daisy-chain fashion as shown in

Figures 4 and 12.
When wired as shown in Figure 12 with two-wire control,

the motor cannot be started or stopped via IMPACC. The

motor starter can only be reset and data obtained via

IMPACC where two-wire control is used.

Automatic reset should not be used with two-wire

control circuit where automatic starting of the motor

may be hazardous.

3

C

GENERIC

PILOT

CIRCUIT

(PLC)

RELAY

P and/or

P

5300C76D

5300C76C

Summary of Contents for Cutler-Hammer W200















Reviews: