11
Instruction Leaflet IL
66A7638H03
Effective December 2010
Instructions for DNP MINT Translator Module
Installation and Use
EATON CORPORATION www.eaton.com
I.L. 66A7638H03
Effective September 2007
11
Counter
Definition
Tag
Defaults
0080
16
DNP Master Station Address
(equivalent to
Section 8.1
, Counter 6)
3072
16
0081
16
DNP MINT’s DNP Address
(equivalent to
Section 8.1
, Counter 7)
FFFF
16
0082
16
DNP MINT’s Configuration Tag
(equivalent to
Section 8.1
, Counter 8)
0001
16
0083
16
DNP MINT’s DNP transfer protocol:
0000
16
Low Byte = Outstation Confirmation Request Enable Bits:
3-0
Data Link Confirmation Retry Count
0
4
Enable Unsolicited Event Data Link Confirm
0
5
Enable Solicited Static/Event Data Link Confirm
0
6
Enable Solicited Static Application Confirm
0
High Byte = Unsolicited Event Generation Bits:
9
Enable Unsolicited Class 1 Events
0
10
Enable Unsolicited Class 2 Events
0
11
Enable Unsolicited Class 3 Events
0
0084
16
DNP network idle time to initiate unsolicited transmission
(1 count = 10ms)
50 = 500ms
0085
16
DNP network unsolicited retry random time increment mask (1 count = 10ms)
007F
16
= 1.27s
0086
16
DNP Data Link Confirmation Wait Timeout
(1 count = 10ms)
50 = 500ms
0087
16
DNP Application Confirmation Wait Timeout
(1 count = 10ms)
500 = 5s
INCOM Scan Level Count To Generate Point Off-Line:
0088
16
Low Byte Scan Level 0 (Poll) Count
(0 – 15)
3
High Byte Scan Level 1 (Interleaved) Count
(0 – 15)
3
0089
16
Low Byte Scan Level 2 (Timer2) Count
(0 – 15)
3
High Byte Scan Level 3 (Timer3) Count
(0 – 15)
3
008A
16
INCOM Level 2 Scan Timer
(1 count = 1s)
300 = 5 min
008B
16
INCOM Level 3 Scan Timer
(1 count = 1s)
900 = 15 min
Table 8: DNP MINT Summary Table Definitions
8.2.2
DNP Address
The DNP Address setting is the DNP destination
address value the DNP MINT will accept in a
request message for one of its DNP MINT or 16
configured devices and thus return as the source
address in the corresponding response message.
It is also applied as the source address in a
generated unsolicited message. A valid setting
is 0000
16
through FFEF
16
. A write request with
an invalid setting will disable access to the
selected DNP MINT objects or device objects on
the DNP network.
8.2.3
Configuration Tag
The Configuration Tag setting provides a label
for the existing configuration table in the DNP
MINT. A request containing a tag setting
corresponding to any of the pre-defined tables
(DNP MINT summary table 01 or device
summary tables 01 through 34) will initialize all
summary settings to the selected pre-defined
values before modifying (over-writing) any of
the other requested counter changes determined
by the write request message.
Acceptance of a write message without the tag
counter request included or with a tag value
outside this pre-defined range will require an
already existing configuration to be resident. A
tag value request of 0 will leave the current tag
value present. A DNP MINT tag value of
FFFF
16
will not be accepted. A device tag value
of FFFF
16
will remove that device from the DNP
MINT. All other tag values will simply be
written as the new tag value.
