background image

26

12. Technical Data

EAFR-101S Arc Point Sensor Relay User Manual

   MN026005EN   February 2016   www.eaton.com

12.2 Auxiliary Voltage

Vaux

(110-220) Vac / (125-250) Vdc 

± 20% 

Maximum Interruption 

100 ms

Maximum Power Consumption

5 W

Standby Current

90 mA

12.3 Trip Relays T1, T2, and T3

Number

3 NO

Rated Voltage

250 Vac/dc

Continuous Carry

5 A

Make and Carry for 0.5 s

30 A

Make and Carry for 3 s

16 A

Breaking Capacity DC, When Time Constant 

L/R=40 ms

40 W; 0.36 A at 110 Vdc

Contact Material

AgNi 90/10

12.4 Binary Output BO1, BO2, and BO3

Rated Voltage

+24 Vdc

Rated Current 

20 mA (max)

Number of Outputs

3

12.5 Binary Inputs BI1, BI2, BI3, BI4, BI5, and BI6

Rated Voltage

+24 Vdc

Threshold Pick up

≥ 16, 88, or 178 Vdc

Threshold Drop off

≤ 15, 75, or 155 Vdc

Rated Current 

3 mA

Number of Inputs

6

12.6 Disturbance Tests

EMC Test

CE approved and tested according 

to EN 50081-2, EN 50082-2

Emission
- Conducted (EN 55011 Class A)

0.15 - 30 MHz

- Emitted (EN 55011 Class A)

30 - 1,000 MHz

Immunity
- Static Discharge (ESD) (According to 

IEC244-22-2 and EN61000-4-2, severity 

Class 4)

Air discharge 15 kV
Contact discharge 8 kV

- Fast Transients (EFT) (According to 

EN61000-4-4, Class III and IEC801-4, 

Level 4)

Power supply input 4 kV, 5/50 ns
Other inputs and outputs 4 kV,  

5/50 ns

- Surge (According to EN61000-4-5 

[09/96], Level 4)

Between wires 2 kV / 1.2/50 µs
Between wire and earth 4 kV / 

1.2/50 µs

- RF Electromagnetic Field Test  

(According. to EN 61000-4-3, Class III)

f = 80 ... 1,000 MHz 10 V/m

- Conducted RF Field (According. to EN 

61000-4-6, Class III)

f = 150 kHz ... 80 MHz 10 V

12.7 Voltage Tests

Insulation Test Voltage Acc - to IEC 60255-5 2 kV, 50 Hz, 1 min
Impulse Test Voltage Acc - to IEC 60255-5

5 kV, 1.2/50 us, 0.5 J

12.8 Mechanical Tests

Vibration Test

10 to 150 Hz, 0.07 mm (.003 in.), 

0.5 gn (60 to 150Hz)
10 to 150 Hz, 1gn (10 to 150Hz)

Shock/Bump Test Acc. to IEC 60255-21-2 20 g, 1,000 bumps/dir.

12.9 Casing and Package

Protection Degree (Front)

IP 50 

Protection Degree (Back)

IP 20

Dimensions - W x H x D mm (W x H x D in.) 45 x 164 x 157 mm

(1.77 x 6.46 x 6.81 in.)

Weight

0.7 kg (24.69 oz)
1.0 kg (35.27 oz) (with package)

12.10 Environmental Conditions

Specified Ambient Service Temp. Range

-35 to 70°C (-31 to 158°F)

Transport and Storage Temp. Range

-35 to 70°C (-31 to 158°F)

Relative Humidity 

Up to 97%

Summary of Contents for EAFR-101S

































Reviews: