Eaton EAFR-101S User Manual Download

Page: 31 / 32

13. Ordering Codes

EAFR-101S Arc Point Sensor Relay User Manual

MN026005EN February 2016 www.eaton.com

13. Ordering Codes

Eaton Catalog Number

Eaton Style Number

Part Number Description

EAFR-110P

65C2010G01

Current, point sensor unit

EAFR-110F

65C2010G02

Current, fiber loop sensor unit

EAFR-101

65C2010G03

Point Sensor unit

EAFR-101D

65C2010G04

Point Sensor unit, DIN Rail mounted

EAFR-102

65C2010G06

Fiber loop sensor unit

EAFR-110PB

65C2010G07

Current, point sensor unit, NC Trip Relay

EAFR-110FB

65C2010G08

Current, fiber loop sensor unit, NC Trip Relay

EAFR-101B

65C2010G09

Point Sensor unit, NC Trip Relay

EAFR-101DB

65C2010G10

Point Sensor unit, DIN Rail mounted, NC Trip Relay

EAFR-102B

65C2010G11

Fiber loop sensor unit, NC Trip Relay

EAFR-01-A

65C2011G01

Arc light point Sensor - 8,000 Lux

EAFR-01-B

65C2011G02

Arc light point Sensor - 25,000 Lux

EAFR-01-C

65C2011G03

Arc light point Sensor - 50,000 Lux

EAFR-06-10

65C2013G01

Arc light plastic fiber sensor - 10 m (32.81 ft)

EAFR-06-15

65C2013G02

Arc light plastic fiber sensor - 15 m (49.21 ft)

EAFR-06-20

65C2013G03

Arc light plastic fiber sensor - 20 m (65.62 ft)

EAFR-06-25

65C2013G04

Arc light plastic fiber sensor - 25 m (82.02 ft)

EAFR-06-30

65C2013G05

Arc light plastic fiber sensor - 30 m (93.43ft)

EAFR-06-35

65C2013G06

Arc light plastic fiber sensor - 35 m (114.83 ft)

EAFR-06-40

65C2013G07

Arc light plastic fiber sensor - 40 m (131.23 ft)

EAFR-07-10

65C2014G01

Arc light glass fiber sensor - 10 m (32.81 ft)

EAFR-07-15

65C2014G02

Arc light glass fiber sensor - 15 m (49.21 ft)

EAFR-07-20

65C2014G03

Arc light glass fiber sensor - 20 m (65.62 ft)

EAFR-07-25

65C2014G04

Arc light glass fiber sensor - 25 m (82.02 ft)

EAFR-07-30

65C2014G05

Arc light glass fiber sensor - 30 m (93.43ft)

EAFR-07-35

65C2014G06

Arc light glass fiber sensor - 35 m (114.83 ft)

EAFR-07-40

65C2014G07

Arc light glass fiber sensor - 40 m (131.23 ft)

EAFR-07-45

65C2014G08

Arc light glass fiber sensor - 45 m (147.64 ft)

EAFR-07-50

65C2014G09

Arc light glass fiber sensor - 50 m (164.05 ft)

EAFR-08-10

65C2015G01

Arc light glass fiber sensor (High Temperature) - 10 m (32.81 ft)

EAFR-08-15

65C2015G02

Arc light glass fiber sensor (High Temperature) - 15 m (49.21 ft)

EAFR-08-20

65C2015G03

Arc light glass fiber sensor (High Temperature) - 20 m (65.62 ft)

EAFR-08-25

65C2015G04

Arc light glass fiber sensor (High Temperature) - 25 m (82.02 ft)

EAFR-08-30

65C2015G05

Arc light glass fiber sensor (High Temperature) - 30 m (93.43ft)

EAFR-08-35

65C2015G06

Arc light glass fiber sensor (High Temperature) - 35 m (114.83 ft)

EAFR-08-40

65C2015G07

Arc light glass fiber sensor (High Temperature) - 40 m (131.23 ft)

EAFR-08-45

65C2015G08

Arc light glass fiber sensor (High Temperature) - 45 m (147.64 ft)

EAFR-08-50

65C2015G09

Arc light glass fiber sensor (High Temperature) - 50 m (164.05 ft)

Summary of Contents for EAFR-101S

































Search results

Summary of Contents for EAFR-101S

Reviews:

Related manuals for EAFR-101S

Brands by name

Popular brands

Eaton EAFR-101S, User Manual

Search results

Summary of Contents for EAFR-101S

Reviews:

Related manuals for EAFR-101S

Brands by name

Popular brands