background image

 

Eaton Small External Battery Cabinet (EBC-S) 
and Large External Battery Cabinet (EBC-L) 

User’s and Installation Guide 

 

© Eaton Corporation plc 2015. All rights reserved.

 

Revision: 002

 

Document ID: P-164000504 

18 (37)

 

 

3.2

 

Installation considerations 

The battery cabinet installation must meet the following guidelines. 

 

Install the system on a level floor suitable for computer or electronic 
equipment. 

 

Install the system in a temperature and humidity controlled indoor 
area free of conductive contaminants and with sufficient air 
exchange. 

The battery cabinet dimensions are shown in Figure 2. 

 

Figure 2. EBC-S and EBC-L dimensions 

A DC-rated circuit breaker within each cabinet provides protection and 
service isolation. 

The battery cabinets use convection cooling to regulate internal 
component temperature. Air inlets are at the bottom of the door and in 
the large battery cabinet also at the bottom of the back wall and outlets 
are on the rear of the cabinet. Allow clearance in front and rear of each 
cabinet for proper air circulation. 

The clearance required around the battery cabinet is shown in Table 1. 

Summary of Contents for EBC-S






































Reviews: