background image

 

Eaton Small External Battery Cabinet (EBC-S) 
and Large External Battery Cabinet (EBC-L) 

User’s and Installation Guide 

 

© Eaton Corporation plc 2015. All rights reserved.

 

Revision: 002

 

Document ID: P-164000504 

29 (37)

 

 

  DANGER 

 

Do not attempt to access any internal area of the battery string 
yourself. Voltages are always present in the battery strings. If you 
suspect that a battery string needs service, contact your service 
representative. 

Observe these precautions when working on or around batteries: 

 

Remove watches, rings, or other metal objects. 

 

Use insulated tools. 

 

Wear rubber gloves and boots. 

 

Do not lay tools or metal parts on top of batteries or battery 
cabinets. 

 

Prior to connecting or disconnecting terminal, disconnect the 
charging source. 

 

Determine if the battery is inadvertently grounded. If it is, remove 
the source of the ground. Contact with any part of a grounded 
battery can result in an electrical shock. The likelihood of such a 
shock is reduced if such grounds are removed during installation 
and maintenance. 

 

When replacing batteries, use the same number of sealed, lead-acid 
batteries. 

 

Dispose of batteries according to your local codes for disposal 
requirements. 

4.2

 

Performing preventive maintenance 

The battery cabinets require very little preventive maintenance. 
However, inspect the system periodically to verify that the units are 
operating normally and that the batteries are in good condition. 

4.2.1

 

Periodic maintenance 

Inspect the UPS periodically to determine if components, wiring, and 
connections exhibit evidence of overheating. Pay particular attention to 
bolted connections. 

Summary of Contents for EBC-S






































Reviews: