2
EG2-NA Ethernet Gateway
www.eaton.com
Contents
INtroductIoN . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Location and spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Ambient atmosphere requirements . . . . . . . . . . . . . . . . . . .4
Mounting Holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Supply Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connecting the Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
iCAN Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Wire Gauge for Supply Terminals . . . . . . . . . . . . . . . . . . . . .4
iCAN Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Setup Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Ethernet Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
iCAN Device Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Factory Default IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . .5
Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Setting the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PC Node Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Ethernet Port Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Reset to Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . .6
WArrANtIES ANd LIMItAtIoN oF LIABILItY . . . . . . . . . . . 7
WArNING
WArNING HAZArdouS VoLtAGES, dIScoNNEct FroM SuPPLY BEForE rEMoVING coVErS
NO USER SERVICEABLE PARTS INSIDE SERVICE BY QUALIFIED PERSONNEL ONLY
SAFEtY INStructIoNS
IMPortANt SAFEGuArdS
rEAd ANd FoLLoW ALL SAFEtY INStructIoNS
The EG2-NA is built and tested to strict safety regulations . By following the steps listed below and elsewhere within this
guide, you can ensure safe installation and operation of these controller units .
●
●
The EG2-NA must be installed only by a qualified electrician
●
●
The installation must comply with the appropriate electrical codes and regulations in force in your area .
●
●
The EG2-NA is designed for indoor installation and use only .
●
●
Ensure that all wiring used conforms fully to local specifications and is sufficiently rated for the installation .
●
●
All new wiring must be fully verified before applying power .
●
●
The high voltage supply should be fed to the EG2-NA via an external isolation breaker with sufficient capacity for the
planned installation .
●
●
Ensure that the supply is fully isolated at an external breaker before removing the chassis covers . Test that power has been
removed before starting to handle conductors .
●
●
Ensure that high voltage and low voltage wiring remains separate .
SAVE tHESE INStructIoNS
