background image

4

Operation

Driving Tips

Proper Starting Gear

Choose a starting gear appropriate for the load and grade conditions, while at 
a stop in Drive and MANUAL modes by using the up/down buttons. Refer to 
Drive Mode for detailed information.

Skip Shifting

Performed in MANUAL by pressing the shift button more than once. Refer to 
MANUAL mode section for detailed information.

Optimal Engine Braking

The LOW mode can be selected while moving. This initiates downshifts as 
soon as possible. Refer to Low mode section for detailed information.

Skid Conditions

If a skid or Antilock brake conditon occurs, disengage the clutch. The Auto-
Shift senses sthe vehicle speed dropping rapidly and will limit downshift gear 
selections until the skid condition is complete.

Cruise Control

The AutoShift is totally compatible with cruise control. If a shift is required 
while cruise control is active, cruise is temporarily interrupted while the shift 
is performed and then automatically resumed after the shift.

Load Based Shifting

In Drive, the AutoShift will adapt to the changing conditions of the vehicle. 
Right after power-up or after changing loads, AutoShift needs to learn the new 
conditions. While learning, it may hold a gear instead of upshifting. Simply 
push the Up button to start the upshift. It may take three or four shifts for the 
AutoShift to learn the new conditions. After that it will handle upshifts and 
downshift automatically. 

Coast Mode

When coasting to a stop in lower gears, AutoShift may not finish downshifting 
until the driver gets back on the throttle. This is normal for the AutoShift. 

Summary of Contents for FO-6406A-ASX























Reviews: