Questions?/Des questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com
1
PACKAGING CONTENTS/CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE
Instruction Manual / Manuel d’instructions/ Instrucciones
®
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user’s authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Install light 10-25 feet above the ground based
on your model.
• Do not mount fixture close to reflective surfaces
such as windows, white walls, white surfaces
and water.
• When installing two fixtures on one switch,
make sure the switch is rated for at least a
1 A inductive load.
• When mounting fixture, make sure the photo
sensor orientation is at the top.
• When mounting to a wall, make sure the fixture
is 7 in. on center away from eave and 13 inches
on center away from inside corner of the
exterior wall.
MOUNTING AND WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing
or servicing.
NOTE:
Fixture can be wall or eave mounted (Fig. 1).
NOTE:
Mounting Bracket (B) mounts to recessed
mounted standard junction boxes (Fig. 2). Junction
box must be at least 1-1/2 inch in depth for proper
installation for recessed mount application.
1.
Line up the slotted holes on the mounting bracket (B)
with the holes on your junction box. Using either (2)
#6 screws or (2) #8 screws (C) (depending on size of
the holes in your junction box), attach the mounting
bracket (B) to your junction box (Fig. 3).
2.
Connect house ground wire to mounting bracket
ground wire using the green screw provided (Fig. 3).
3.
Connect fixture black wire to house black wire, and
fixture white wire to house white wire, using the wire
nuts (E) provided (Fig. 4).
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Outdoor weatherproof silicone caulking
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Fixture designed for wall or eave mount to a junction box only. Mount fixture to a
grounded, recessed-mounted standard junction box marked for use in wet locations.
• Do not mount below 5 feet.
FCC DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following 2
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equip-
ment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off an on, the user is encouraged to try to correct the
interference by one or more of the following measures:
A.
Light fixture
Appareil d’éclairage
Accesorio
ENGLISH
C.
(2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
(2) vis nº 6 de 32 x 3/4 po et 2 vis nº 8 de 32 x 3/4 po pou
boîtier de jonction (choisissez la dimension convenant
à votre boîtier de jonction)
(2) Tornillos #6-32 x 3/4 pulg. y (2) tornillos #8-32 x 3/4
pulg. para montaje de la caja de conexiónes (utilice el
tamaño que mejor se adecue a su caja de conexiónes)
E.
(2) Wire nuts
(2) Serre-fils
(2) Tuercas para cables
D.
(2) Fixture Mounting Screws
(2) Vis de montage
(2) Tornillos de montaje del accesorio
WARNING
B.
Mounting bracket
Support de montage
Soporte de montaje
1A
Wall mount
Eave mount
1B
(White/Blanc/Blanco)
FT28VCW
FT28VCIW
FT18VCW
FT18VCIW
(Bronze/Bronze/Bronce)
FT28VCB
FT28VCIB
FT18VCB
FT18VCIB
3
B
Junction box
Round
1-1/2 in.
Octagonal
1-1/2 in.
2
