1
Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com
Instruction Manual / Manuel d’instructions/ Instrucciones
1.
Remove wire guard (B) and glass lens (C).
2.
Remove lens gasket.
3.
Remove two screws on socket plate and set
aside (Fig. 1).
4.
Mount housing (A) to either 1/2 in. hanging conduit
or to a surface using the two tabs and mounting
screws (sold separately).
5.
Apply silicone caulk around the base of the housing
and junction box or around the conduit to provide a
watertight seal against rain and moisture.
WIRING YOUR FIXTURE
1.
Connect the white house supply wire to the white
fixture wire using a wire connector (sold separately).
Connect the black house supply wire to the black
fixture wire using a wire connector (sold separately).
Connect the house supply ground wire to the
fixture ground wire using a wire connector
(sold separately).
2.
Attach socket plate to the housing (A) and fasten
securely with screws, making sure no wires are
sticking out from underneath the housing (A).
NOTE:
Make sure gasket is seated correctly.
3.
Replace the lens gasket and install lamp.
4.
Install glass lens (C) and lens guard (B). Tighten
guard set screw.
5.
Turn on the main power at the main fuse/breaker box.
CARE AND MAINTENANCE
1.
Turn off power at main fuse or circuit breaker
before installing or servicing.
2.
Always use or replace bulb with the same wattage
or lower wattage than required. Installing a bulb of
higher wattage could create a fire hazard. Using
higher wattage bulbs will void the warranty.
NOTE:
If lens is replaced, use only tempered safety
glass of equal thickness per UL requirements.
2-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Eaton warrants to customers that, for a period of two years from the date of purchase, Eaton
products will be free from defects in materials and workmanship. The obligation of Eaton
under this warranty is expressly limited to the provision of replacement products. This
warranty is extended only to the original purchaser of the product. A purchaser’s receipt or
other proof of date of original purchase acceptable to Eaton. This is required before warranty
performance shall be rendered. This warranty does not apply
PACKAGING CONTENTS/
CONTENIDO DEL PAQUETE
/ CONTENU DE L’EMBALLAGE
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Flat head screwdriver
• (1) 100 watt (max.) incandescent A-19 bulb
• Wire connectors
• (2) Mounting screws
• Weatherproof silicone caulk
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• For outdoor use only.
• cULus LISTED for wet location use.
NOTE:
Failure to follow instructions may result in improper operation or void the warranty.
• Read and follow these instructions.
• To reduce the risk of a burn during relamping, disconnect power supply to the unit
before relamping.
• Disconnect at fuse or circuit breaker before installing or servicing.
• Disconnect power and allow fixture to cool before changing bulb or handling fixture.
• Edges may cut. Handle with care.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• For wall or ceiling mount application.
• This fixture should not be used in enclosed or improperly ventilated areas with
a high ambient temperature.
• FOR SUPPLY CONNECTIONS, USE WIRE RATED FOR AT LEAST 125°C.
SAVE THESE INSTRUCTIONS AND WARNINGS.
MOUNTING THE FIXTURE
WARNING: Risk of electric shock. Disconnect power at fuse or circuit breaker before
installing or servicing.
NOTE:
Make certain that the fixture is connected to a 120-volt power source. UL-approved
wire connectors should be used. Be sure no loose strands of wire are sticking out from under
your wire connectors.
VT100G
VT100GH
A.
Fixture housing
Luminaria
Boîtier du luminaire
ENGLISH
B.
Guard
Protección
Protecteur
C.
Glass lens
Lente de vidrio
Lentille en verre
Fig. 1
1/2 inch threaded
conduit openings
Socket
plate
Guard
set
screw
A
WARNING
