Technical Specification
i-on30EX/EXD
Page 36
EN50131-6 ratings
The i-on30EX/EXD provides space for one 7Ah
battery.
For Security Grade 2 the required battery standby
time is 12 hours. This means that all the devices
powered by the backup battery, including the
control unit and at least one keypad, should
together draw no more in total than an average of
580mA over a 12 hour standby time.
The table below shows the current consumption of
the control unit and each device that can be fitted
to it.
CIE power
requirement:
100mA min.
120mA max
i-kp01 power
requirement:
30mA (backlight off)
45mA/65mA (backlight
norm/bright)
60mA in alarm
KEY-
KPZ01/KP01/K01
power requirement
35mA backlight OFF,
internal prox reader only.
65mA max backlight ON,
external prox reader
connected
Wired Expander
requirement
20mA max quiescent.
300mA in alarm if
sounder connected.
Radio Expander
requirement
40mA max quiescent
320mA in alarm if
sounder connected.
Battery charging
requirement:
200mA (recharge within
72 hrs)
Plug-on
Communicator power
requirement:
i-sd02, i-dig02:
20mA quiescent
50mA max
Plug-on
Communicator power
requirement
i-gsm02:
150mA quiescent
and max.
Plug-by
Communicator pins
require:
5mA each when active.
10 FSL zones
20mA
5 four-wire CCL zones
30mA
12V Bus output
voltage range :
10±0.5V to 13.8V
12V Aux output
voltage range:
10±0.5V to 13.8V
12V Bell output
voltage range
10±0.5V to 13.8V
Max p-to-p ripple
voltage:
0.5V
Standby Battery:
12V, 7Ah sealed lead
acid (not supplied).
‘Low battery’ fault at:
< 12V
Aux power output fault
at:
< 9V
Deep discharge
protection at:
10±0.5V
Serviceable
components:
Mains fuse: 250mA (T)
Standby time:
See “Power Availability”
on page 12.
Electromagnetic
Compatibility
Immunity
Conforms to EN50130-4.
Emissions
Conforms to EN61000-6-3.
Outputs
Panel:
O/P 1, Bell,
Strobe
Open collector transistor,
+12VDC when inactive, 0V
when active. 500mA max.
Plug-by O/P 1-
12
Open collector transistor
+12VDC when inactive, 0V
when active, 50mA max.
LS
(loudspeaker)
Min impedance 16 Ohm per
output, current consumption =
280mA in alarm.
Expander:
Outputs
Open collector transistor,
+12VDC when inactive, 0V
when active. 500mA max.
Note: The current is limited by
the amount available from the
power supply driving the
expander.
KEY-KPZ01
Outputs
Open collector transistor,
+12VDC when inactive, 0V
when active, 500mA max.
Sounder Volume Levels (at 1m)
i-kp01 (at max volume)
70dB
Expander piezo sounder
70dB
Panel/Expander 16 Ohm loudspeaker
93dB
Fuses
The control unit has a replaceable T250mA mains
fuse.
Electrical Safety
Conforms to EN60950-1.
Other
If you wish to connect the i-on30EX/EXD control
unit to a PC using the USB port then make sure
that the cables have the following specifications:
USB
Mini-B plug for control unit end,
USB-A for PC end. Max length
3m.
Radio Expander and Keypads
Radio
Operating frequency
868.6625MHz Narrowband.
EN 300 220-3.
EN 300 330-2
Transmitter
range
The range of the transmitters
compatible with this control unit
depends on the environment in
which they are installed. As a
guideline, most transmitters will
work at in excess of 200m
range in free space conditions.
