background image

FIELD INSTALLED UPM INSTALLATION PLAN AND UNPACKING

Power Xpert 

9395P Field Installed UPM Mechanical Installation Manual  

S

  P-164000503 Rev 1

 

3-2

Table 3‐1. FI-UPM Cabinet Maximum Weight

Model

Maximum Weight 

kg (lb)

Shipping

Installed

Power Xpert 9395P FI-UPM

496 (1094)

471 (1037)

The FI-UPM cabinet uses forced air cooling to regulate internal component
temperature. Air inlets are in the front of the cabinet and outlets are in the top. Allow
clearance in front of and above each cabinet for proper air circulation. The clearances
required around the FI-UPM cabinet are shown in Table 3‐2. Dimensions are in
millimeters (inches).

Table 3‐2. FI-UPM Cabinet Clearances

From Top of Cabinet

457.2 mm (18

) minimum clearance for ventilation

From Front of Cabinet

914.4 mm (36

) working space

From Back of Cabinet

None Required

From Right Side of Cabinet

None Required

From Left Side of Cabinet

None Required

The basic environmental requirements for operation of the FI-UPM are:

S

Ambient Temperature Range:

0–40°C (32–104°F)

S

Recommended Operating Range: 20–25°C (68–77°F)

S

Maximum Relative Humidity:

95%, non-condensing

The FI-UPM ventilation requirements are shown in Table 3‐3.

Table 3‐3. FI-UPM Air Conditioning or Ventilation Requirements During Full Load Operation

Rating

Input/Output Voltage

Heat Rejection

kW (1000 BTU/hr)

Ventilation Required for

Cooling Air Exhaust

225 kVA

480/480

7.9 (27.1)

Approximately

950 liter/sec

(2000 CFM)

250 kVA

480/480

9.3 (31.9)

275 kVA

480/480

10.6 (36.1)

300 kVA

480/480

10.6 (36.1)

Summary of Contents for Power Xpert 9395P

































Reviews: