background image

10

Eaton PXGMS Card Quick Start Instructions P-164000208—Rev 06

Figure 10. Name Services Settings

7.

Select

Yes

for the message, “

Do you want to save the Network Configuration?

8.

Wait for approximately two minutes for the card to reboot. Initially, all lights will be lit. You will know the
card has finished rebooting when only the top light (Status) and the bottom light (Power) remain lit.

9.

Open a browser and enter the default IP address (

https://169.254.0.101

for firmware 2.6.0 or later,

http://192.168.200.101

for earlier firmware versions).

10. When prompted, log on as administrator:

For firmware 2.6.5 and higher the username is “admin” and the default password is the card's MAC
address (case sensitive with no colons).

For example: Card's MAC address: 00:E0:D8:FF:C0:C4

Administrator name: admin

Password: 00E0D8FFC0C4

For firmware versions older than 2.6.5 the default username and password is “admin”.

The PXGMS card Web page displays.

11. Click

Network

in the menu list.

12. Does the DHCP-assigned IP address display?

If yes, uncheck (disable) the DHCP Enabled box and select

Apply

.

Obtain a DHCP-Assigned IP Address

Summary of Contents for Power Xpert Gateway Minislot



























Reviews: