background image

14

Instruction Booklet 

IB015001EN

Effective June 2015

Power Xpert Solar DC 

breaker recombiner 

  

EATON 

www.eaton.com

Table 2.  Initial insulation resistance test record
Date

All overcurrent devices open

Phase-to-phase connections

Phase-to-ground connections

POSITIVE—NEGATIVE

POSITIVE—Ground 

NEGATIVE—Ground

Date

All overcurrent devices closed

Phase-to-phase connections

Phase-to-ground connections

POSITIVE—NEGATIVE 

POSITIVE—Ground 

NEGATIVE—Ground

Notes:

Date

All overcurrent devices open

Phase-to-phase connections

Phase-to-ground connections

POSITIVE—NEGATIVE 

POSITIVE—Ground 

NEGATIVE—Ground

Date

All overcurrent devices closed

Phase-to-phase connections

Phase-to-ground connections

POSITIVE—NEGATIVE 

POSITIVE—Ground 

NEGATIVE—Ground

Notes:

Date

All overcurrent devices open

Phase-to-phase connections

Phase-to-ground connections

POSITIVE—NEGATIVE 

POSITIVE—Ground 

NEGATIVE—Ground

Date

All overcurrent devices closed

Phase-to-phase connections

Phase-to-ground connections

POSITIVE—NEGATIVE 

POSITIVE—Ground 

NEGATIVE—Ground

Notes:

Date

All overcurrent devices open

Phase-to-phase connections

Phase-to-ground connections

POSITIVE—NEGATIVE 

POSITIVE—Ground 

NEGATIVE—Ground

Date

All overcurrent devices closed

Phase-to-phase connections

Phase-to-ground connections

POSITIVE—NEGATIVE 

POSITIVE—Ground 

NEGATIVE—Ground

Notes:

Summary of Contents for Power Xpert

















Reviews: