background image

PDU OPERATING INSTRUCTIONS

EATON 

Powerware

®

 225 kVA PDU Installation and Operation Manual  

S

  164201629 Rev D

 www.powerware.com

6−14

Operation

Subfunction

Function

Contrast Adjust

Select 

CONTRAST

 from the System Setup Level 0 menu to display the Contrast Adjust screen.

Use the left or right arrow pushbuttons to adjust the contrast for the LCD. When the contrast
adjustment is complete, press the 

SAVE

 pushbutton

.

 Once the setting is saved, the System Setup

screen displays. To return to the System Setup screen without saving the setting, press the return
arrow pushbutton

.

Versions

The Versions screen provides the firmware version numbers installed on the PDU. Select

VERSIONS

 from the System Setup Level 0 menu to display the Versions screen. To scroll through

the firmware types, press the up or down arrow pushbuttons on the menu bar. To return to the
System Setup screen, press the return arrow pushbutton

.

System Setup Level 1

The System Setup Level 1 screen can be used to change the Level 1 password, set the PDU date
and time, clear the History Log, clear the Profile Log, set up the modem, set up the building alarms,
and log out of Level 1. In addition, all of the Level 0 functions are available. A password is required
to access the Level 1 functions.

Enter Password

If not already in a system setup menu, press the 

SETUP

 pushbutton on the main menu bar to

display the System Setup Level 0 Screen. Select 

ENTER PASSWORD

 from the System Setup

Level 0 menu to display the Enter Password screen. Use the left or right arrow pushbuttons to
select the password character position. Use the up or down arrow pushbuttons to change the
password character. Once the password is entered, press the 

DONE

 pushbutton. The System

Setup Level 1 menu screen is displayed. The default password is L1.

Function Selection

Use the up or down arrow pushbuttons to highlight the setup function screen desired, then press
the 

SELECT

 pushbutton to display the function screen. The Level 1 screen times out after

60 minutes or can be logged out at any time by selecting the 

LOG OUT

 function from the menu

screen. When logged out the screen returns to the Level 0 screen.

Display (change Password)

The Display (change password) screen allows the System Setup Level 1 password to be changed.
Select 

CHANGE PASSWORD

 from the System Setup Level 1 menu to display the Display (change

password) screen. Use the left or right arrow pushbuttons to select the password character
position. Use the up or down arrow pushbuttons to change the password character. Once the
new password is entered, press the 

DONE

 pushbutton

.

 The Display (change password save)

screen is displayed.

Display (change password
save)

The Display (change password save) screen lets the user save the new password, retry another
password, or abort the password change. Press 

SAVE

RETRY

, or 

ABORT

. If SAVE or ABORT is

pressed, the action is completed, and the System Setup screen displays. If RETRY is pressed, the
Display (change password) screen is redisplayed.

Set Date and Time
MM/DD/YYYY

The Set Date and Time MM/DD/YYYY screen allows the internal date and time of the PDU to be set
in the month/day/year format. The date and time information is used for display on the screen and
for logging events in the Event and History Logs. Use the left or right arrow pushbuttons to
highlight the setting to be changed. Use the up or down arrow pushbuttons to make the change.
When finished making changes, use the left or right arrow pushbuttons to highlight SAVE and the
up or down arrow pushbuttons to select YES. To complete the save function and return to the
System Setup screen, select the return arrow pushbutton

.

Clear History

The Clear History screen allows the History Log to be cleared. Select 

CLEAR HISTORY

 from the

System Setup Level 1 menu to display the Clear History screen. Use the 

CLEAR

 pushbutton to

clear the log. To return to the System Setup screen without clearing the log, press the 

CANCEL

pushbutton.

Clear Load Profile

The Clear Load Profile screen allows the Profile Log to be cleared. Select 

CLEAR LOAD PROFILE

from the System Setup Level 1 menu to display the Clear Load Profile screen. Use the 

CLEAR

pushbutton to clear the log. To return to the System Setup screen without clearing the log, press
the 

CANCEL

 pushbutton.

Modem Setup

The Modem Setup screen is used to change and save the settings for the X−Slot modem. Select

MODEM SETUP

 from the System Setup Level 1 menu to display the Modem Setup screen. Use

the up or down arrow pushbuttons to highlight the setup function screen desired, then press the

SELECT

 pushbutton

.

 To return to the System Setup screen, press the return arrow pushbutton

.

Summary of Contents for Powerware 225 kVA Three-Phase Power Distribution...















































































































































Reviews: