background image

EATON 

Powerware

®

 225 kVA PDU Installation and Operation Manual  

S

  164201629 Rev D

 www.powerware.com

3−1

Chapter 3

Installing the PDU

3.1

Preliminary Installation Information

W

 

A

 

R

 

N

 

I

 

N

 

G

Installation should be performed only by qualified personnel.

Refer to the following while installing the PDU:

S

Appendix A contains installation drawings and additional installation notes.

S

Dimensions are in millimeters and inches.

S

Do not tilt the cabinets more than 

"

10° during installation.

S

Remove the conduit landing plates to add conduit landing holes or remove
knockouts, as required. Plate material is 16 gauge steel (1.5 mm/0.060

"

 thick).

S

Install the cabinets on a level concrete or non−combustible floor suitable for
computer or electronic equipment.

S

If installing with a UPS, refer to the applicable UPS Installation and Operation
manual for UPS cabinet wiring requirements and conduit and terminal locations.

S

See Table A on page A−2 for equipment weight and point loading.

3.2

Unloading the PDU from the Pallet

The PDU cabinet is bolted to a pallet consisting of four angle metal supports secured
to two four−inch by six−inch wood supports.

W

 

A

 

R

 

N

 

I

 

N

 

G

S

The PDU is heavy (see Table A on page A−2). If unloading instructions are not closely followed, the
cabinet may cause serious injury.

S

Do not install a damaged cabinet. Report any damage to the carrier and contact an Eaton service
representative immediately.

S

Do not tilt the PDU more than 10° from vertical or the cabinet may tip over.

NOTE  

Verify that the forklift is rated to handle the weight of the cabinet (see Table A on page A−2 for

cabinet weight).

1.

If not already moved, use a forklift to move the cabinet to the installation site, or
as close as possible, before unloading from the pallet. Insert the forklift jacks
between the skids on the bottom of the unit.

2.

Unfasten the front door latch and swing the doors open.

3.

Loosen the screws securing the inside distribution panel doors, and swing the
doors open.

4.

If the leveling feet are not fully retracted, turn the leveling feet until they are
retracted.

Figure 3Table 3

Summary of Contents for Powerware 225 kVA Three-Phase Power Distribution...















































































































































Reviews: