English
6. Repeat this procedure from step 1 for the other equipment
you want to control (VCR, DVD, SAT,...). If your equipment
(TV, SAT, etc....) does not respond, try the other codes for
your brand. If it still doesn't respond, try the manual code
search method (4.4 Manual code search).
4.3 Automatic code search for some well-known brands
If your brand is listed hereafter, you can use the brand
search method (faster than the "manual" and the "automatic
code search").
BRAND
CODE
BRAND
CODE
Philips & Sub brands / Radiola
1
Telefunken / Saba /
Normende
4
Sony / Panasonic / JVC / Sharp
/ Akai / Toshiba / Daewoo
2
Grundig / Blaupunkt
5
& Other Japanese brands
Thomson / Brandt / Ferguson
3
Nokia / Finlux / ITT &
Other Scandinavian
6
brands
1. Turn on the device you want to control.
2. Press and hold
SETUP
(8) until the LED indicator (2)
lights steadily. Release
SETUP
button.
3. Press the mode button (3) that matches the equipment
you wish to control. The LED (2) blinks once.
4. Enter the code corresponding to your brand, point the
XanuraHome Remote in the direction of your equipment,
press
CHAN+
(5) once only. Continue to point the
XanuraHome Remote at your equipment until the equipment
changes Channel (the remote control sends an IR signal
every second. Please wait until your equipment reacts).
When your equipment does react, press on the key -/-- (11)
to confirm. If you accidentally miss the code, you can stop
the autosearch by pressing
CHAN-
( 5) and by repeatedly
pressing this key return to the right code. Press -/-- (11) to
confirm.
Remark:
if some functions of your equipment don't work,
you need to try another code for your brand. The search
function starts after the last confirmed code. For example, if
it was 030, the search function starts at 031, and it will keep
on trying until the last possible code.
4.4 Automatic code search for all brands
When searching an unknown code, you can step through the
library automatically (AutoSearch). When your equipment
responds, you can stop the searching process and store the
code you found.
Note: as you can dedicate any appliance (TV, DVD, SAT...)
to VCR, CBL, DVD, etc. keys, you need first to enter any 3
digit code for the kind of appliance you wish to control (found
in the code book), i.e.: If you want to program a SAT under
the VCR key, enter ANY SAT code found in the code book
and then follow the steps below:
1. Turn on the device you want to control.
2. Press and hold
SETUP
(8) until the LED indicator (2)
lights steadily. Release
SETUP
button.
3. Press the mode button (3) that matches the equipment
you wish to control. The LED (2) blinks once.
4. Press
CHAN+
(5) once. After a few seconds the remote
starts stepping through the code library (fast search, 1 code
26
MBO 1991494G01 001
per second). When the device responds, you can press
CHAN+
(5) to switch to slow search (1 code per 3 seconds).
You can step back by pressing
CHAN-
(5) (you can step
forward by pressing
CHAN+
(5) in case you went too far
back). As soon as the device responds again, press the -/-key
(11) to store the code you found.
Remark:
if some functions of your equipment don't work,
you need to try another code for your brand. The
search function starts after the last confirmed code. For
example, if it was 030, the search function starts at 031, and
it will keep on trying until the last possible code.
4.5 Manual code search
Note: as you can dedicate any appliance (TV, DVD, SAT...)
to the VCR, CBL, DVD, etc. keys, you first need to enter any
3 digit code for the kind of appliance you wish to control
(found in the code book), i.e.: If you want to program a SAT
under the AUX key, enter ANY SAT code found in the code
book and then follow the steps below:
1. Make sure your equipment is switched on.
2. Press and hold
SETUP
(8) until the LED indicator lights
steadily. Release
SETUP
3. Press the mode key (3) that matches the equipment you
want to control (for example TV).
4. Press
CHAN+
(5) repeatedly until the channel changes. If
you step past the correct code use
CHAN-
(5) to go back to
the right code.
5. When the equipment you want to control reacts, press -/-(
11) to confirm the code.
Note: If your equipment doesn't have
CHAN+
you can use
PLAY
(VCR or DVD) (19) or
POWER
(1) key.
Note:
if certain functions of your equipment can't be
controlled you will have to find a different code for your
brand. The search starts after the last registered code. If that
was 030, the search starts at 031 until the last possible code
and then goes from 000 to 029.
4.6 Learning codes
Your XanuraHome Remote contains the codes for most TVs,
videos etc. in its code library. If a certain device is not in this
library, you can learn the codes for your existing remote
control. The library may also contain a code that works for
your device, but which misses a few function buttons. You
can then select to only learn those buttons (maximum of 150
buttons).
Master clear
You can use the MASTER CLEAR method to clear the
learning memory. It is advised to execute a MASTER
CLEAR before you start learning any commands.
1. Keep the
SETUP
(8) pressed until one of the Mode LED's
stays lit. Release the SETUP (8) button.
2. Press the
LEARN
(24) button twice. The LED will flash
every time you press the button.
3. Press
SETUP
(8). The LED will extinguish after a few
seconds.
27
MBO 1991494G01 001
